Mercury GRAND MARQUIS recalls by model year

Reported: 1983-02-24 (February 24, 1983) · Model years: 1983

THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.

Remedy: THE DEALER WILL REPLACE THE TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIP AT NO CHARGE TO OWNER.

Reported: 1983-03-07 (March 7, 1983) · Model years: 1983

THE PARKING GEAR MAY NOT ENGAGE, EVEN THOUGH THE GEAR SHIFT LEVER IS PLACED IN THE "PARK" POSITION. THIS OCCURS IF THE LINKAGE INSIDE THE TRANSMISSION THAT ACTUATES THE PARK GEAR WAS IMPROPERLY MANUFACTURED. A PIN THAT RETAINS COMPONENTS ON A LINKAGE (ACTUATING) ROD COULD BREAK AND THE LINKAGE MAY NOT ENGAGE THE PARKING GEAR.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE PARKING PAWL ACTUATING ROD ASSEMBLY.

Reported: 1983-12-20 (December 20, 1983) · Model years: 1984

THE BOLTS THAT ATTACH THE D-SHAPED RING FOR THE SHOULDER BELT ARE INADEQUATELY SUPPORTED BY THE MATERIAL IN WHICH THEY ARE MOUNTED. THE ATTACHMENT DOES NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES".

Remedy: DEALERS WILL INSTALL NEW ATTACHING HARDWARE TO IMPROVE THE STRENGTH OF THE MOUNTING.

Reported: 1987-09-04 (September 4, 1987) · Model years: 1986, 1987

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Consequence: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

Reported: 1987-02-09 (February 9, 1987) · Model years: 1987

STEERING CENTERLINKS MAY BREAK AT A BEND LOCATION.

Consequence: STEERING CONTROL WOULD BE DIMINISHED, WITH REDUCEDCONTROL OF LEFT WHEEL ONLY AND CONSIDERABLE STEERING WHEEL FREE PLAY.

Remedy: REPLACE STEERING CENTERLINK.

Reported: 1987-08-17 (August 17, 1987) · Model years: 1987

FUEL RAILS MAY BE BENT SO THAT NO. 5 INJECTOR CUPS ARE OUT OF DESIGN POSITION.

Consequence: BENT FUEL RAIL COULD CAUSE A FUEL LEAK, WHICH INPRESENCE OF AN IGNITION SOURCE COULD RESULT IN AN ENGINE FIRE.

Remedy: REPLACE FUEL RAIL ASSEMBLIES AS NECESSARY.

Reported: 1988-03-08 (March 8, 1988) · Model years: 1987, 1988

AUTOMATIC RETRACTOR FOR SEAT BELTS FOR DUAL FACING REAR SEATS MAY BE INSTALLED IN AN IMPROPER LOCATION.

Consequence: SEAT BELT COULD BIND BETWEEN SEAT CUSHION AND SEAT BACKCAUSING THE RETRACTOR TO BE SLUGGISH OR UNABLE TO TAKE UP EXCESS BELT SLACK.

Remedy: REMOVE AND PROPERLY INSTALL THE RIGHT AUXILIARY SEAT BELTS.

Reported: 1996-04-25 (April 25, 1996) · Model years: 1988, 1989

THE IGNITION SWITCH COULD EXPERIENCE AN INTERNAL SHORT CIRCUIT.

Consequence: THIS CONDITION COULD CAUSE OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN AREA OF THE VEHICLE.

Remedy: DEALERS WILL REPLACE THE IGNITION SWITCH.

Reported: 1991-03-18 (March 18, 1991) · Model years: 1991

THE PARK ROD ASSEMBLY CONTAINS A PARK CAM WITH INADEQUATE SURFACE HARDNESS, WHICH COULD LEAD TO PARK DISENGAGEMENT OR NO PARK ENGAGEMENT WHEN THE LEVER IS PLACED IN PARK.

Consequence: IF PARK IS NOT ENGAGED AND THE PARKING BRAKE IS OFF, AVEHICLE ROLL-AWAY COULD RESULT.

Remedy: REPLACE PARK ROD ASSEMBLY ON AUTOMATIC TRANSMISSIONS.

Reported: 2007-08-03 (August 3, 2007) · Model years: 1992, 1993, 1994, 1995, 1996, 1997, 1998

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Consequence: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

Reported: 2008-02-04 (February 4, 2008) · Model years: 1992, 1993, 1994, 1995, 1996, 1997, 1998

FORD IS RECALLING 225,000 MY 1992-2003 ECONOLINE, MY 1993-1995 TAURUS SHO, MY 1992-1998 CROWN VICTORIA, MY 1993 BRONCO, F-SERIES, MY 1995-1997 F-SERIES SUPER DUTY STRIPPED CHASSIS, MY 1992-1998 MERCURY GRAND MARQUIS, AND MY 1992-1995 LINCOLN TOWN CAR VEHICLES. THE AFFECTED VEHICLES WERE PREVIOUSLY REPAIRED USING A WIRING HARNESS THAT IS NOT COMPATIBLE WITH THE VEHICLE CIRCUIT POLARITY.

Consequence: AS A RESULT, THE FUSE IS LOCATED IN THE OUTPUT CIRCUIT RATHER THAN IN THE INTENDED INPUT POWER FEED CIRCUIT, AND MAY NOT OFFER THE INTENDED PROTECTION IN THE EVENT OF AN ELECTRICAL SHORT TO GROUND.

Remedy: DEALERS WILL INSTALL A NEW WIRING HARNESS, OR REPLACE THE MATING ELECTRICAL COMPONENT. THE RECALL BEGAN ON FEBRUARY 18, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.

Reported: 1999-05-19 (May 19, 1999) · Model years: 1992, 1993

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SPEED CONTROL DEACTIVATION SWITCH CAN DEVELOP A RESISTIVE SHORT IN THE ELECTRICAL CIRCUIT THAT COULD POTENTIALLY RESULT IN AN UNDERHOOD FIRE. A FIRE IS POSSIBLE BOTH WHEN THE VEHICLE IS RUNNING AND WHEN THE VEHICLE ENGINE IS OFF. ALSO, THE SHORT COULD DISABLE THE SPEED CONTROL SYSTEM OR CAUSE THE BRAKE LIGHT FUSE TO OPEN.

Consequence: A FIRE CAN ORIGINATE IN THE LEFT FRONT UNDERHOOD AREA.

Remedy: DEALERS WILL INSTALL A NEW SPEED CONTROL DEACTIVATION SWITCH AND CONNECTOR SHELL. OWNER NOTIFICATION BEGAN MAY 20, 1999.

Reported: 1994-08-09 (August 9, 1994) · Model years: 1994

THE NUTS AND BOLTS THAT ATTACH THE REAR BRAKE ADAPTOR TO THE AXLE HOUSING FLANGE CAN LOOSEN AND EVENTUALLY SEPARATE. IF ONE OR MORE OF THE NUTS COME OFF THE BOLTS, DAMAGE TO THE PARKING BRAKE ASSEMBLY OR TO THE ANTILOCK BRAKE SYSTEM (ABS) SENSOR AND SENSOR RING (IF SO EQUIPPED) WILL OCCUR. IF ALL FOUR NUTS ON ONE END OF THE AXLE COME OFF THE BOLTS, DAMAGE TO THE BRAKE HYDRAULIC LINE OR THE PARKING BRAKE CABLE CAN OCCUR.

Consequence: OCCURRENCE OF ANY OF THESE CONDITIONS CAN RESULT IN A LOSS OF BRAKING CAPABILITY AND POSSIBLE ACCIDENT.

Remedy: DEALERS WILL INSPECT AND, IF NEEDED, INSTALL NEW BOLTS. IF ANY OF THE FASTENERS ARE DISCONNECTED, THE PARKING BRAKE AND ABS COMPONENTS WILL BE INSPECTED AND SERVICED.

Reported: 1995-03-27 (March 27, 1995) · Model years: 1995

THE SEAL MATERIAL BETWEEN THE FUEL FILLER PIPE AND FUEL TANK MAY NOT HAVE BEEN FULLY CURED DURING THE MOLDING PROCESS WHICH COULD ALLOW FOR FUEL LEAKAGE.

Consequence: FUEL LEAKAGE COULD RESULT IN A VEHICLE FIRE IF AN IGNITION SOURCE WERE PRESENT.

Remedy: DEALERS WILL REPLACE THE FUEL FILLER PIPE-TO-FUEL TANK SEAL WITH A NEW SEAL OF DIFFERENT MATERIAL.

Reported: 1995-10-02 (October 2, 1995) · Model years: 1995

THESE VEHICLES WERE BUILT WITH THE NON-CYCLING POWER WINDOW CIRCUIT BREAKER AND THE CYCLING HEADLAMP CIRCUIT BREAKER INTERCHANGED.

Consequence: IN THE EVENT OF A SHORT OR OVERLOAD IN THE HEADLAMPCIRCUIT, BOTH HEADLAMPS CAN GO OUT WITHOUT WARNING, RATHER THAN FLASHING AS INTENDED WITH THE CYCLING CIRCUIT BREAKER. THIS COULD LEAD TO REDUCED NIGHT TIME DRIVER VISIBILITY, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT THESE VEHICLES, REMOVE THE CIRCUIT BREAKER AND REINSTALL THE BREAKER IN THE CORRECT LOCATIONS.

Reported: 1996-03-05 (March 5, 1996) · Model years: 1995

THE RIVETS HOLDING THE REAR OUTBOARD BELT D-RINGS WERE NOT HEAT TREATED PROPERLY CAUSING THE HEADS OF THE RIVETS TO FRACTURE UNDER LOAD AND FAIL TO HOLD THE D-RINGS TO THE STRAPS. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THIS CONDITION CAN REDUCE THE RESTRAINING CAPABILITIES OF THE SAFETY BELT IN THE EVENT OF AN ACCIDENT.

Remedy: DEALERS WILL INSTALL A REINFORCEMENT PLATE ON THE REAR OUTBOARD SEAT BELT ASSEMBLY ANCHORAGES INVOLVED IN THIS CAMPAIGN.

Reported: 2000-06-12 (June 12, 2000) · Model years: 1996, 1997, 1998, 1999, 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Consequence: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

Reported: 2000-06-12 (June 12, 2000) · Model years: 1996, 1997, 1998, 1999, 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Consequence: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

Reported: 1996-04-22 (April 22, 1996) · Model years: 1996

WHEN IN THE SECONDARY LATCHED POSITION, THE DRIVER DOOR LATCHES MAY OPEN WHEN SUBJECTED TO TRANSVERSE LOADS LESS THAN THAT SPECIFIED IN FMVSS NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."

Consequence: THE DRIVER'S DOOR, WHEN CLOSED ONLY TO THE SECONDARY LATCHED POSITION, MAY NOT SUSTAIN A 1,000 POUND TRANSVERSE LOAD.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER DOOR LATCH.

Reported: 2000-07-18 (July 18, 2000) · Model years: 1998, 1999, 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.

Consequence: IF THIS OCCURS AND ANY PORTION OF THE OPERATOR'S BODY IS UNDER THE VEHICLE, THE POTENTIAL FOR PERSONAL INJURY EXISTS.

Remedy: OWNERS WILL BE PROVIDED WITH A REVISED JACK INSTRUCTION AND STOWAGE CARD AND JACK WARNING LABEL, AS WELL AS A SUPPLEMENT TO THE OWNER GUIDE.

Reported: 2000-02-17 (February 17, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH LOWER THAN THE INTENDED LEVEL OF TORQUE ON THE BOLTS THAT ATTACH THE AIR BAG ELECTRONIC CRASH SENSOR MODULE TO THE VEHICLE.

Consequence: A LOOSE MODULE COULD RESULT IN A DELAYED AIR BAG DEPLOYMENT IN THE EVENT OF A VEHICLE CRASH.

Remedy: DEALERS WILL TIGHTEN THE AIR BAG ELECTRONIC CRASH SENSOR ATTACHING BOLTS.

Reported: 2000-03-20 (March 20, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH THE LEFT REAR SEAT BELT RETRACTOR ATTACHING BOLTS INCORRECTLY TIGHTENED.

Consequence: IN THE EVENT OF A CRASH, THE VEHICLE OCCUPANT MAY NOT BE PROPERLY RESTRAINED, INCREASING THE RISK OF PERSONAL INJURY.

Remedy: DEALERS WILL TIGHTEN THE RETRACTOR MOUNTING BOLTS TO THE SPECIFIED TORQUE.

Reported: 2000-05-17 (May 17, 2000) · Model years: 2000

VEHICLE DESCRIPTION: A WINDSHIELD WIPER CONTROL MODULE MAY NOT BE CAPABLE OF CARRYING THE CURRENT REQUIRED DURING HIGH LOAD CONDITIONS ON THE WIPERS (I.E., ICE, SNOW, OR OTHER DEBRIS).

Consequence: THIS CONDITION COULD RESULT IN INOPERATIVE WIPERS WITH NO ADVANCE WARNING.

Remedy: DEALERS WILL INSPECT THE WIPER CONTROL MODULES AND REPLACE IF NECESSARY.

Reported: 2000-09-13 (September 13, 2000) · Model years: 2001

CERTAIN PASSENGER VEHICLES, LIMOUSINES, AND MINI VANS WERE BUILT WITH A NEWLY DESIGNED RESTRAINT CONTROL MODULE (RCM). IN SOME CASES, THE RCM DOES NOT RECOGNIZE CERTAIN SYSTEM FAULTS THAT COULD RESULT IN AN AIR BAG OR SEAT BELT PRE-TENSIONER UNEXPECTEDLY ACTIVATING DURING THE SELF-TEST SEQUENCE AT VEHICLE START-UP.

Consequence: THIS CONDITION COULD RESULT IN PERSONAL INJURY.

Remedy: DEALERS WILL REPLACE THE RCM IN THESE VEHICLES. OWNER NOTIFICATION BEGAN SEPTEMBER 14, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

Reported: 2000-12-06 (December 6, 2000) · Model years: 2001

VEHICLE DESCRIPTION: MINIVANS AND PASSENGER VEHICLES. A RESTRAINT CONTROL MODULE (RCM) OR A SIDE OR FRONT CRASH SENSOR MAY HAVE BEEN ASSEMBLED WITH ONE OR MORE OF THE SCREWS THAT MOUNT THE CIRCUIT BOARD IN THE HOUSING MISSING. IF SOME OR ALL OF THE SCREWS ARE MISSING, THE PERFORMANCE OF THE OCCUPANT RESTRAINS COULD BE AFFECTED.

Consequence: IN SOME CASES, LESS THAN THE INTENDED LEVEL OF PROTECTION IN THE EVENT OF A CRASH.

Remedy: DEALERS WILL INSPECT THE RCM AND CRASH SENSORS AND, IF NECESSARY, REPLACE THEM.

Reported: 2001-07-16 (July 16, 2001) · Model years: 2001

VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01.

Consequence: IN THE EVENT OF A CRASH, THE RESTRAINT SYSTEM MAY NOT PROVIDE ADEQUATE OCCUPANT PROTECTION, INCREASING THE RISK OF PERSONAL INJURY TO THE SEAT OCCUPANT.

Remedy: DEALERS WILL INSPECT THE FRONT OUTBOARD SEAT BELT BUCKLES AND IF THE BUCKLE FAILS THE INSPECTION PROCESS, IT WILL BE REPLACED. OWNER NOTIFICATION BEGAN JULY 25, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Reported: 2015-12-22 (December 22, 2015) · Model years: 2003, 2004, 2005

Ford Motor Company (Ford) is recalling certain model year 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles manufactured October 3, 2001, to August 2, 2005. The affected vehicles have a lighting control module (LCM) that may fail, resulting in a loss of headlights.

Consequence: A loss of headlights can reduce driver visibility and increase the risk of a crash.

Remedy: Ford will notify owners, and dealers will replace the LCM, free of charge. The recall began April 14, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S39.

Reported: 2005-11-09 (November 9, 2005) · Model years: 2005

ON CERTAIN PASSENGER VEHICLES, THE BATTERY CABLE INCLUDES A FUSIBLE LINK THAT MAY CONTACT AND SUBSEQUENTLY CHAFE ON A #2 CROSS MEMBER ATTACHING BOLT.

Consequence: THIS CONDITION MAY RESULT IN HEAT DAMAGE AND COULD LEAD TO A FIRE.

Remedy: DEALERS WILL INSPECT THE FUSIBLE LINK AND POSITION IT AWAY FROM THE CROSS MEMBER BOLT. IF THE FUSIBLE LINK HAS ALREADY CHAFED AND COPPER WIRES HAVE BEEN EXPOSED, THE FUSIBLE LINK WILL BE REPLACED. THE RECALL BEGAN ON NOVEMBER 18, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673, OR LINCOLN/MERCURY AT 1-800-521-4140.

Reported: 2013-08-29 (August 29, 2013) · Model years: 2005, 2006, 2007, 2008, 2009, 2010, 2011

Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.

Consequence: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.

Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.

Reported: 2014-11-05 (November 5, 2014) · Model years: 2005, 2006, 2007, 2008, 2009, 2010, 2011

Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.

Consequence: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.

Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.

Reported: 2006-11-15 (November 15, 2006) · Model years: 2007

CERTAIN PASSENGER VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, 'WINDSHIELD MOUNTING.' THE WINDSHIELD MAY NOT BE PROPERLY SECURED TO THE VEHICLE BODY.

Consequence: IF THE WINDSHIELD IS NOT PROPERLY RETAINED TO THE VEHICLE, WIND NOISE, SQUEAK/RATTLES AND/OR WATER LEAKS MAY OCCUR. ALSO, LOSS OF WINDSHIELD RETENTION MAY REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.

Remedy: DEALERS WILL REPLACE THE WINDSHIELD FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 22, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.

Reported: 2007-06-26 (June 26, 2007) · Model years: 2008

ON CERTAIN PASSENGER VEHICLES, A FRONT WHEEL BEARING AND HUB ASSEMBLY MAY FRACTURE DUE TO IMPROPER HEAT TREATMENT.

Consequence: IF A HUB FRACTURES, IT MAY POTENTIALLY DETACH FROM THE WHEEL KNUCKLE, RESULTING IN THE WHEEL BEING RETAINED ONLY BY THE BRAKE CALIPER ASSEMBLY. AS A RESULT, THE WHEEL MAY SEPARATE FROM THE VEHICLE POTENTIALLY RESULTING IN A CRASH.

Remedy: DEALERS WILL INSPECT BOTH FRONT WHEEL BEARING AND HUB ASSEMBLIES AND REPLACE THEM FREE OF CHARGE. THE RECALL BEGAN ON JUNE 22, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.