Chevrolet C10 recalls by model year

Reported: 1967-01-23 (January 23, 1967) · Model years: 1967

Reported: 1970-08-10 (August 10, 1970) · Model years: 1970

Reported: 1970-10-21 (October 21, 1970) · Model years: 1971

Reported: 1974-02-15 (February 15, 1974) · Model years: 1973, 1974

Reported: 1974-04-25 (April 25, 1974) · Model years: 1974

Reported: 1977-10-14 (October 14, 1977) · Model years: 1976, 1977

THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVER"S FOOT IS REMOVED FROM THE PEDAL.

Remedy: DEALER WILL INSTALL A NEW ACCELERATOR PEDAL AND RETAINER DESIGNED TO PREVENT THE ACCELERATOR PEDAL ROD FROM CUTTING THE RUBBER MAT OR CARPET. THIS WILL BE PERFORMED WITHOUT CHARGE.

Reported: 1977-10-12 (October 12, 1977) · Model years: 1977

THE INVOLVED VEHICLES WERE ASSEMBLED WITH A STANDARD FRONT SUSPENSION ASSEMBLY, INSTEAD OF THE SPECIFIED HEAVY-DUTY FRONT SUSPENSION. OPERATION OF VEHICLE WHILE CARRYING THE MAXIMUM RATED LOAD MAY LEAD TO DETERIORATION AND EVENTUAL FAILURE OF FRONT SUSPENSION COMPONENTS.

Remedy: DEALER WILL INSTALL THE PROPER FRONT SUSPENSION COMPONENTS WITHOUT CHARGE TO OWNER.

Reported: 1981-10-05 (October 5, 1981) · Model years: 1981

THE SPARE WHEEL IS ONE INCH WIDER THAN THE MAXIMUM APPROVED RIM WIDTH AND FAILS TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS".

Remedy: THE SPARE WHEEL ASSEMBLY WILL BE REPLACED WITHOUT CHARGE TO OWNER.

Reported: 1981-12-14 (December 14, 1981) · Model years: 1981

THE HYDRAULIC BRAKE FLUID USED IN CERTAIN VEHICLES MAY FAIL TO COMPLY WITH THE BRAKE FLUID BOILING POINT REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 116, "MOTOR VEHICLE BRAKE FLUIDS". BRAKING EFFICIENCY MAY BE REDUCED AND VEHICLE STOPPING DISTANCE INCREASED, ESPECIALLY WHEN HARD OR FREQUENT BRAKING RAISES BRAKE FLUID TEMPERATURE.

Remedy: SUSPECT HYDRAULIC BRAKE FLUID WILL BE BLED FROM THE BRAKE SYSTEM AND REPLACED WITH GM DELCO SUPREME NO. 11 OR AN EQUIVALENT, WITHOUT CHARGE.

Reported: 1982-12-14 (December 14, 1982) · Model years: 1982

ON THE INVOLVED VEHICLES, THE REAR BRAKE DRUM BALANCE WEIGHTS MAY INTERFERE WITH THE ALUMINUM WHEELS. THIS CONTACT COULD CAUSE THE WHEEL LUG NUTS TO LOOSEN, LEADING TO WHEEL STUD FAILURE. THIS COULD ALLOW SEPARATION OF THE WHEEL AND TIRE FROM THE VEHICLE.

Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, MODIFY THE REAR BRAKE DRUM BALANCE WEIGHTS WITHOUT CHARGE TO OWNER.

Reported: 1983-04-27 (April 27, 1983) · Model years: 1982

THE LOCKING SCREW THAT RETAINS THE PINION SHAFT IN PLACE IN THE DIFFERENTIAL COULD COME LOOSE. THE PINION SHAFT TURNS THE GEARS INSIDE THE DIFFERENTIAL THAT ROTATE THE DRIVE AXLES AND REAR WHEELS. IF THE LOCKING SCREW COMES LOOSE, IT COULD DAMAGE OTHER COMPONENTS OR JAM IN THE GEARS. IF THE PINION SHAFT COMES LOOSE, THE REAR WHEELS MAY NO LONGER POWER THE VEHICLE.

Remedy: THE DEALER WILL REPLACE THE DIFFERENTIAL LOCK SCREW AT NO CHARGE.

Reported: 1987-04-01 (April 1, 1987) · Model years: 1985, 1986

IMPROPER SIZE REAR BRAKE ASSEMBLIES WERE INSTALLED.

Consequence: TRUCKS COULD EXCEED THE MAXIMUM STOPPING DISTANCEPERMITTED BY FMVSS 105, HYDRAULIC BRAKE SYSTEMS, CREATING THE POTENTIAL FOR AVEHICLE CRASH.

Remedy: REPLACE REAR AXLE BRAKE ASSEMBLIES WITH PROPER SIZE ASSEMBLIES.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

CRUISE CONTROL CABLE LOCK MECHANISM MAY SELF DISENGAGE CAUSING ERRATIC OPERATION OR THROTTLE NOT RETURNING TO IDLE.

Consequence: ENGINE SPEED WOULD NOT DECREASE; LOSS OF ACCELERATORCONTROL COULD RESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A CLAMP AROUND THE LOCK TAB OF CRUISE CONTROL.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

ONE OR BOTH OF OUTER TIE ROD NUTS MAY BE LOOSE AND NOT CRIMPED.

Consequence: LOSS OF ONE OR BOTH NUTS COULD LEAD TO TIE RODDISENGAGING FROM STEERING KNUCKLE RESULTING IN POSSIBLE LOSS OF STEERINGCONTROL AND POSSIBLY A CRASH.

Remedy: REPLACE TIE ROD AND KNUCKLE AND SET TOE-IN.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

TRUCKS MAY HAVE CRACKED OR BROKEN DOOR STRIKER NUTS, WHICH DO NOT CONFORM TO FMVSS 206.

Consequence: IN A COLLISION, CRACKED OR BROKEN STRIKER NUT COULDALLOW DOOR TO OPEN UNEXPECTEDLY AND POSSIBLY CAUSE INJURY TO OCCUPANTS.

Remedy: REPLACE EXISTING DOOR STRIKER NUTS.

Reported: 1987-09-01 (September 1, 1987) · Model years: 1988

RIGHT AND LEFT HAND BRAKE HOSE MAY CONTACT THE WHEEL OR TIRE IN A FULL TURN.

Consequence: IF THE HOSE MAKES CONTACT WITH THE WHEEL OR TIRE IT WILLEVENTUALLY WEAR THE HOSE TO A POINT OF RUPTURE, RESULTING IN A LOSS OF THEFRONT BRAKES. LOSS OF FRONT BRAKES WOULD INCREASE THE STOPPING DISTANCE WHENMINIMUM TIME IS REQUIRED AND COULD RESULT IN A VEHICLE CRASH.

Remedy: INSTALL NEW REPOSITIONING BRACKETS FOR THE FRONT BRAKE HOSES.

Reported: 1993-02-01 (February 1, 1993) · Model years: 1988, 1989, 1990, 1991, 1992, 1993

UNANTICIPATED HEAT IN THE TRANSMISSION CAN FORCE THE TRANSMISSION FLUID OUT OF THE VENT TUBE.

Consequence: THE VENTED TRANSMISSION FLUID CAN CATCH FIRE IF EXPOSEDTO A SOURCE OF IGNITION.

Remedy: INSTALL A LONGER TRANSMISSION VENT HOSE ROUTED TO THE LEFT SIDE OF THE ENGINE COMPARTMENT OF THE VEHICLE.

Reported: 1989-05-15 (May 15, 1989) · Model years: 1989

THERE MAY BE BELOW SPECIFIED TORQUE ON THE TRAILER HITCH ATTACHING FASTENERS, ALLOWING THE TRAILER HITCH TO MOVE UNDER TOWING LOADS.

Consequence: FASTENERS COULD FAIL; IF THIS OCCURS WHILE TRAILERIS BEING PULLED, HITCH AND TRAILER COULD SEPARATE AND A VEHICLE CRASH COULDOCCUR WITHOUT PRIOR WARNING.

Remedy: CORRECT TORQUE IN TRAILER HITCH FASTENERS TO PREVENT TRAILER SEPARATION.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1992, 1993

VEHICLES ALTERED BY PAS, INC. HAVE COMPRESSED NATURAL GAS FUEL TANKS THAT CAN DEVELOP STRESS CORROSION, WHICH CRACK THE E-GLASS WRAPPING. THIS STRESS CORROSION CRACKING CAN LEAD TO TANK RUPTURES.

Consequence: IF THE TANK RUPTURES, PERSONAL INJURY TO INDIVIDUALS IN OR NEAR THE VEHICLE MAY OCCUR.

Remedy: GM IS OFFERING TO EXCHANGE THESE VEHICLES WITH A COMPARABLY EQUIPPED 1994 GASOLINE 1/2 OR 3/4 TON GM PICKUP. IF THE OWNER CHOOSES NOT TO EXCHANGE THE NATURAL GAS VEHICLE, GM WILL REPURCHASE THE VEHICLE.

Reported: 1999-05-20 (May 20, 1999) · Model years: 1992

VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.

Reported: 1995-12-21 (December 21, 1995) · Model years: 1993, 1994

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1993-09-15 (September 15, 1993) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993) · Model years: 1994

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1994

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1994-10-26 (October 26, 1994) · Model years: 1994

THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.

Remedy: DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

Consequence: IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

Remedy: DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

Reported: 1998-07-01 (July 1, 1998) · Model years: 1994, 1995, 1996

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.

Consequence: THIS CONDITION CAN RESULT IN INOPERATIVE WIPERS, REDUCING A DRIVER'S VISIBILITY, AND INCREASING THE RISK OF A VEHICLE CRASH.

Remedy: DEALERS WILL REPLACE THE WIPER MOTOR CIRCUIT BOARD AND COVER.

Reported: 1999-02-05 (February 5, 1999) · Model years: 1994

VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

Consequence: THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.

Reported: 1996-01-02 (January 2, 1996) · Model years: 1995

THE STEERING COLUMN UPPER INTERMEDIATE-SHAFT NUT MAY NOT BE TORQUED TO PROPER SPECIFICATIONS. THE NUT COULD LOOSEN AND DETACH ALLOWING THE THROUGH-BOLT THAT SECURES THE UPPER INTERMEDIATE-SHAFT TO THE LOWER STEERING COLUMN SHAFT JOINT TO FALL OUT.

Consequence: THIS LOOSE ENGAGEMENT CAN PROVIDE NOTICEABLE NOISE AND ABNORMAL STEERING FEELING TO THE DRIVER AND, IF LEFT UNATTENDED, THE STEERING SHAFTS CAN SEPARATE RESULTING IN A LOSS OF STEERING CONTROL.

Remedy: DEALERS WILL TORQUE THE SUSPECT FASTENERS TO THE PROPER SPECIFICATIONS.

Reported: 1996-04-04 (April 4, 1996) · Model years: 1995, 1996

THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, "ACCELERATOR CONTROL SYSTEMS."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE ENGINE SPEED MAY NOT RETURN TO IDLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT FOR ADEQUATE THROTTLE CABLE TO DASH MAT CLEARANCE, AND IF THERE IS INSUFFICIENT CLEARANCE, CUT OUT A PORTION OF THE DASH MAT TO PROVIDE PROPER CLEARANCE.

Reported: 1997-03-07 (March 7, 1997) · Model years: 1995, 1996, 1997

VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.

Consequence: THIS PINCHING CAN CUT THE HAND OR POSSIBLY SEVER THE FINGER(S) WITHOUT PRIOR WARNING.

Remedy: DEALERS WILL INSTALL A PROTECTOR COVER OVER THE RECLINER MECHANISM.

Reported: 1998-08-10 (August 10, 1998) · Model years: 1995, 1996, 1997, 1998

VEHICLE DESCRIPTION: CREW CAB PICKUP TRUCKS. THE FRONT, INNER CORNER OF THE FUEL TANK CAN CONTACT THE BODY SILL EITHER INTERMITTENTLY OR CONSTANTLY. THIS MOVEMENT CAN CAUSE A DISCERNIBLE NOISE AND, OVER TIME, CAN WEAR A HOLE IN OR CRACK THE FUEL TANK AT POINT OF CONTACT.

Consequence: THIS CONDITION CAN RESULT IN FUEL LEAKAGE AND A DISTINCT FUEL ODOR IF THE TANK WERE FILLED ABOVE THE LEVEL OF THE HOLE OR CRACK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD RESULT.

Remedy: DEALERS WILL INSPECT THE FUEL TANK FOR WEAR AND, EITHER INSTALL A SPACER BETWEEN THE FUEL TANK AND THE FRONT CROSSMEMBER, OR IF NECESSARY, REPLACE THE FUEL TANK.

Reported: 1995-12-28 (December 28, 1995) · Model years: 1996

CERTAIN TRUCKS HAVE FUEL RAIL ASSEMBLIES WITH AN IMPROPERLY CRIMPED END RETAINER CLIP THAT RESULTS IN A FUEL LEAK.

Consequence: IF FUEL LEAKAGE OCCURS AND AN IGNITION SOURCE IS PRESENT, AN ENGINE COMPARTMENT FIRE COULD OCCUR.

Remedy: DEALERS WILL INSPECT THE FUEL RAIL ASSEMBLY AND REPLACE ANY FUEL RAIL ASSEMBLY WITH A JULIAN DATE CODE OF 95318 THROUGH 95338.

Reported: 1996-05-07 (May 7, 1996) · Model years: 1996

THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.

Consequence: VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.

Reported: 1997-10-07 (October 7, 1997) · Model years: 1997

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS. ONE OR TWO OF THE FRONT SEAT MOUNTING BOLTS WERE NOT INSTALLED. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 207, "SEATING SYSTEMS."

Consequence: IN THE EVENT OF A VEHICLE CRASH, A SEAT WITH THIS CONDITION WILL NOT PROTECT THE OCCUPANT AS REQUIRED BY THE STANDARD.

Remedy: DEALERS WILL CHECK ALL SEAT MOUNTING BOLTS AND INSTALL ANY MISSING BOLTS.

Reported: 1998-02-17 (February 17, 1998) · Model years: 1998

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. ONE OR BOTH FRONT BRAKE ROTOR/HUBS WERE BUILT WITH AN OUT-OF-SPECIFICATION GRAY IRON THAT CAN FAIL DURING THE LIFE OF THE VEHICLE.

Consequence: IF A DRIVER CONTINUES TO DRIVE WITH A CRACKED ROTOR, THE CRACKS COULD CONTINUE AROUND THE WHEEL MOUNTING BOLT CIRCLE AND ULTIMATELY RESULT IN A WHEEL SEPARATION.

Remedy: DEALERS WILL INSPECT THE ROTORS FOR A CORE DATE OF "287" AND, IF FOUND, REPLACE THE ROTOR.

Reported: 2000-04-27 (April 27, 2000) · Model years: 1999

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES DO NOT COMPLY WITH THE OCCUPANT PROTECTION REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE RIGHT FRONT PASSENGER RESTRAINT SYSTEMS MAY NOT MEET THE NECK EXTENSION REQUIREMENTS.

Remedy: DEALERS WILL INSTALL A TRAY INSERT ON THE TOP OF THE PASSENGER SIDE OF THE INSTRUMENT PANEL. THE TRAY INSERT CORRECTS THE NONCOMPLIANCE.

Reported: 2000-08-08 (August 8, 2000) · Model years: 2000

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH VACUUM POWER, 4-WHEEL DISC BRAKES. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS." THESE VEHICLES WERE BUILT WITH A KINKED BRAKE BOOSTER VACUUM SUPPLY HOSE.

Consequence: THESE VEHICLES DO NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 105.

Remedy: DEALERS WILL RE-ROUTE THE BRAKE BOOSTER VACUUM SUPPLY HOSE.

Reported: 2001-04-10 (April 10, 2001) · Model years: 2001

VEHICLE DESCRIPTION: CERTAIN 2-WHEEL DRIVE PICKUP TRUCKS FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." THE PROBLEM WAS CAUSED BY A COMPUTER ERROR THAT RESULTED IN THE CERTIFICATION LABEL LISTING TIRE SIZE AND INFLATION PRESSURE INFORMATION THAT DIFFER FROM THE TIRE SIZE AND THE INFLATION PRESSURE INFORMATION FOR THE TIRES ON THE VEHICLE. IF THE VEHICLE OWNER OR SOMEONE SERVICING THE VEHICLE INFLATES THE TIRES ACCORDING TO THE PRESSURE SPECIFIED ON THE LABEL VERSUS THE APPROPRIATE PRESSURE FOR THE TIRES, THE TIRES COULD BE UNDER-INFLATED OR OVER-INFLATED DEPENDING ON THE TIRES MOUNTED ON THE VEHICLE.

Consequence: IF THE TIRES ARE UNDER-INFLATED, IT COULD REDUCE THE TREAD LIFE OF THE TIRE, AND THE TIRE COULD DEGRADE TO A POINT OF ALLOWING SUDDEN AIR LOSS. IF THE TIRES ARE OVER-INFLATED, IT COULD REDUCE THE TREAD LIFE OF THE TIRE AND INCREASE SUSCEPTIBILITY TO ROAD HAZARD DAMAGE. IF SUDDEN AIR LOSS OR A ROAD HAZARD CAUSES DAMAGE TO A TIRE, CONTROL OF THE VEHICLE COULD BE ADVERSELY AFFECTED AND COULD RESULT IN A VEHICLE CRASH.

Remedy: OWNERS WILL BE PROVIDED WITH A NEW LABEL AND INSTALLATION INSTRUCTIONS. HOWEVER, A DEALER CAN INSTALL THE LABEL IF THE OWNER SO DESIRES. OWNER NOTIFICATION BEGAN MAY 31, 2001. OWNERS WHO DO NOT RECEIVE THE LABEL AND INSTALLATION INSTRUCTIONS WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR GMC AT 1-800-462-8782.