Nissan QUEST recalls by model year

Reported: 2000-12-15 (December 15, 2000) · Model years: 1993, 1994, 1995, 1996, 1997, 1998

VEHICLE DESCRIPTION: MINIVANS. THE FUEL TANK VENT HOSE ALLOWS AIR TO VENT FROM THE FUEL TANK DURING REFUELING. CRACKS HAVE DEVELOPED IN THE VENT HOSE. IF (1) THE FUEL TANK IS OVERFILLED, NOT ALLOWING EXCESS FUEL IN THE VENT HOSE TO FLOW BACK INTO THE TANK, (2) THE VEHICLE IS DRIVEN ONLY A SHORT DISTANCE AFTER REFUELING AND, (3) THERE IS SUBSEQUENTLY SIGNIFICANT HEATING OF THE FUEL TANK, THE FUEL IN THE TANK CAN EXPAND INTO THE VENT HOSE AND LEAK FUEL.

Consequence: FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE CAN RESULT IN A FIRE.

Remedy: DEALERS WILL REPLACE THE VENT HOSE.

Reported: 1992-09-21 (September 21, 1992) · Model years: 1993

THE SERVICE BRAKE MASTER CYLINDER WAS NOT PROPERLY ASSEMBLED OR COULD HAVE BEEN DAMAGED BY THE EVACUATION AND FILLING OF THE BRAKE SYSTEM AT THE ASSEMBLY PLANT.

Consequence: THIS CAN RESULT IN A PARTIAL BRAKE SYSTEM FAILURE DUE TOINTERNAL MASTER CYLINDER LEAKAGE WHICH CAN CAUSE LOSS OF BRAKING ON TWO OF THEFOUR WHEELS. IF THIS OCCURS, THERE WOULD BE INCREASED BRAKE PEDAL TRAVEL, HIGHERPEDAL EFFORTS AND INCREASED STOPPING DISTANCES.

Remedy: A NEW BRAKE MASTER CYLINDER WILL BE INSTALLED.

Reported: 1992-09-21 (September 21, 1992) · Model years: 1993

ONE OR BOTH OF THE BOLTS SECURING THE AUTOMATIC SEAT BELT RESTRAINT SYSTEM TRACKS TO THE B-PILLARS WERE NOT ADEQUATELY TIGHTENED.

Consequence: THIS CONDITION CAN RESULT IN THE AUTOMATIC SEAT BELTSYSTEM TRACK JOINTS HAVING LESS THAN DESIGN STRENGTH, AND INCREASE THE RISK OFINJURY TO THE SEAT OCCUPANT IN THE EVENT OF A COLLISION OR SUDDEN STOP.

Remedy: DEALERS WILL TIGHTEN THE PASSIVE RESTRAINT SYSTEM TRACK MOUNTING BOLTS.

Reported: 1992-12-02 (December 2, 1992) · Model years: 1993

FUEL FILLER HOSES MAY HAVE BEEN CUT PRIOR TO INSTALLATION BY A UTILITY KNIFE USED TO OPEN THE SHIPPING BOX.

Consequence: FUEL LEAKAGE CAN RESULT IF THE CUT EXTENDED THROUGH THETHICKNESS OF THE HOSE WALL. LEAKING FUEL CAN RESULT IN A FIRE IF EXPOSEDTO A SOURCE OF IGNITION.

Remedy: REPLACE THE FUEL FILLER HOSE.

Reported: 1995-11-22 (November 22, 1995) · Model years: 1993

LEAVES AND OTHER FOREIGN MATERIAL CAN ENTER THROUGH THE COWL PANEL AIR INTAKE DURING OPERATION OF THE FRONT HEATER AND/OR AIR CONDITIONING SYSTEM RESULTING IN A BUILD-UP OF MATERIAL IN THE PLENUM. THIS CAN LEAD TO NOISE, ODORS, OR IN SOME CASES, IGNITION OF THESE MATERIALS.

Consequence: A VEHICLE FIRE COULD OCCUR.

Remedy: DEALERS WILL INSTALL AN ADDITIONAL HEATER/AIR CONDITIONING SYSTEM INTAKE SCREEN.

Reported: 1998-08-17 (August 17, 1998) · Model years: 1994, 1995

THE REAR LAMP SOCKET MAY NOT ILLUMINATE BECAUSE THE METAL CAN IN THE LAMP SOCKET MOVES OR SEPARATES FROM THE PLASTIC SOCKET HOUSING.

Consequence: THIS CAN RESULT IN MALFUNCTION OF THE STOP OR REAR RUNNING LAMPS. CENTER HIGH MOUNT STOP LAMP FUNCTION IS UNAFFECTED. REAR LAMP MALFUNCTION CAN RESULT IN FOLLOWING DRIVERS NOT BEING ALERTED TO THE SUBJECT VEHICLE'S PRESENCE OR INTENDED ACTIONS, PARTICULARLY IN THE CASE IN WHICH BOTH LAMPS HAVE MALFUNCTIONED.

Remedy: DEALERS WILL INSTALL A REVISED REAR LAMP SOCKET AND WIRING ASSEMBLIES.

Reported: 1996-06-04 (June 4, 1996) · Model years: 1995

AN OUT-OF-SPECIFICATION CONDITION IN THE SEAT CABLE ROLLER PULLEY ASSEMBLY CAN ALLOW THE CABLE THAT CONNECTS THE SEAT ADJUST LEVER TO THE LATCH TO BE PINCHED IN THE ROLLER ASSEMBLY.

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THIS CONDITION CAN PREVENT THE LATCH ON THE LEFT SIDE FROM FULLY ENGAGING THE SEAT RAIL. THIS DOES NOT COMPLY WITH THE REQUIREMENT OF FMVSS NO. 207, "SEATING SYSTEMS."

Remedy: DEALERS WILL REPLACE THE PULLER ASSEMBLY IN THE THIRD ROW SLIDING BENCH SEAT LATCH ASSEMBLY.

Reported: 1998-03-03 (March 3, 1998) · Model years: 1996

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES WERE PRODUCED WITH POWER WINDOWS THAT CAN BE CLOSED AFTER THE IGNITION KEY IS TURNED TO THE "OFF" POSITION AND THE RIGHT FRONT (PASSENGER) DOOR IS OPENED. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS 118, "POWER-OPERATED WINDOW SYSTEMS."

Consequence: THERE IS THE POTENTIAL FOR UNSUPERVISED CHILDREN TO OPERATE THE POWER WINDOWS, INCREASING THE RISK OF PERSONAL INJURY TO THE CHILD.

Remedy: OWNERS WILL BE PROVIDED WITH A LABEL REMINDING OWNERS NOT TO LEAVE CHILDREN UNATTENDED BECAUSE THE POWER WINDOWS CAN OPERATE FOR 15 MINUTES AFTER THE VEHICLE IGNITION HAS BEEN TURNED OFF UNLESS THE DRIVER'S DOOR IS OPENED. ALSO INCLUDED ARE INSTRUCTIONS DESCRIBING HOW AND WHERE THIS LABEL IS TO BE INSTALLED. IF AN OWNER PREFERS, THEIR DEALER CAN INSTALL THIS LABEL FOR THEM.

Reported: 1997-10-28 (October 28, 1997) · Model years: 1997

VEHICLE DESCRIPTION: PASSENGER MINI VANS EQUIPPED WITH AUTOMOTIVE BATTERIES SUPPLIED BY GNB TECHNOLOGIES. THESE BATTERIES HAVE A DEFECTIVE NEGATIVE POST THAT CAN CAUSE ACID LEAKAGE AND RELATED CORROSION DAMAGE.

Consequence: THIS CONDITION CAN CAUSE A CATASTROPHIC FAILURE OF THE BATTERY WHICH COULD LEAD TO AN ENGINE FIRE OR BATTERY EXPLOSION.

Remedy: DEALERS WILL REPLACE THESE BATTERIES. UNTIL A NEW BATTERY IS OBTAINED, OWNERS SHOULD NOT ATTEMPT TO "JUMP START" THESE BATTERIES.

Reported: 2000-10-02 (October 2, 2000) · Model years: 1999, 2000

VEHICLE DESCRIPTION: MINI VANS. ONE OR MORE OF THE FIVE BOLTS THAT MOUNT THE RACK AND PINION STEERING GEAR TO THE VEHICLE MAY HAVE BEEN INCORRECTLY TIGHTENED.

Consequence: THERE COULD BE A LOOSENESS IN THE STEERING, WHICH MAY BE ACCOMPANIED BY NOISE OR VIBRATION.

Remedy: DEALERS WILL INSPECT THE VEHICLES AND, IF THE BOLTS ARE MISSING, WILL REPLACE THE STEERING GEAR MOUNTING BOLTS. ALL BOLTS WILL BE TIGHTENED TO THE SPECIFIED TORQUE.

Reported: 1999-03-25 (March 25, 1999) · Model years: 1999

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH E-Z ENTRY SEATS. THE AFFECTED VEHICLES MAY HAVE A SECOND ROW RIGHT HAND SIDE CAPTAIN CHAIR THAT HAS INADEQUATE LUBRICATION OF THE EASY ENTRY AND EXIT LATCH SYSTEM. IN SOME CASES, THE ACTUATOR SPRING IN THE LATCH COULD DEFORM AFTER REPEATED USE, CAUSING THE LATCH TO REMAIN IN THE UNLATCHED POSITION. IF THIS OCCURS, THE SEAT WILL SLIDE FREELY ON THE SEAT TRACK AND THE SPRINGS ON THE TRACK WILL MOVE THE SEAT TO THE EASY ENTRY POSITION TOWARD THE FRONT OF THE VEHICLE.

Consequence: AN UNLATCHED SEAT TRACK COULD RESULT IN AN INCREASED RISK OF INJURY IN THE EVENT OF A VEHICLE CRASH.

Remedy: DEALERS WILL REPLACE THE SEAT TRACK FOR THE SECOND ROW RIGHT HAND SIDE CAPTAIN'S CHAIR, WHICH INCLUDES THE EASY ENTRY AND EXIT LATCH MECHANISM.

Reported: 1999-08-05 (August 5, 1999) · Model years: 1999

VEHICLE DESCRIPTION: MINI VANS. THE FUEL TANK RETENTION STRAP (TWO STRAPS PER VEHICLE) CAN BREAK AT THE SPOT WELDS CAUSING AN UNDERBODY RATTLE.

Consequence: THERE IS ALSO A POTENTIAL FOR FUEL TANK SEPARATION OR FUEL LEAK, INCREASING THE RISK OF A FIRE.

Remedy: DEALERS WILL REPLACE THE FUEL TANK RETENTION STRAPS.

Reported: 1999-12-20 (December 20, 1999) · Model years: 1999

VEHICLE DESCRIPTION: MINIVANS AND LIGHT DUTY TRUCKS. THE TAIL LIGHT SOCKET MAY HAVE BEEN IMPROPERLY MOLDED, RESULTING IN THE LOCKING TAB HAVING INSUFFICIENT FORCE TO RETAIN THE BULB.

Consequence: IF THE BULB FALLS OUT OF THE SOCKET, THE BRAKE OR TAIL LAMP FUNCTION CANNOT OCCUR.

Remedy: DEALERS WILL REPLACE THE TAIL LAMP SOCKETS.

Reported: 2000-09-07 (September 7, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON CERTAIN SEAT BELT BUCKLES OF YOUR VEHICLE AND REPLACE ALL SEAT BELT BUCKLES THAT FALL WITHIN THE SUSPECT DATE CODE RANGE.

Reported: 2000-10-27 (October 27, 2000) · Model years: 2001

VEHICLE DESCRIPTION: MINI VANS. THESE VEHICLES MAY HAVE THE PLASTIC TRIM COVER AROUND THE BASE OF THE FRONT SEAT SAFETY BELT BUCKLE TRAPPED BETWEEN THE SHOULDER OF THE RESTRAINT ANCHORAGE BOLT AND THE SEAT PEDESTAL. THIS COULD EVENTUALLY ALLOW THE SEAT BELT BUCKLE BOLT TO LOOSEN.

Consequence: IN THE EVENT OF A CRASH, THE OCCUPANT SEATED IN THAT LOCATION MAY NOT BE ADEQUATELY RESTRAINED, INCREASING THE RISK OF PERSONAL INJURY.

Remedy: DEALERS WILL INSPECT THE SEAT BELT BUCKLE ASSEMBLY ATTACHMENT. SOME BELT BUCKLE ASSEMBLIES MAY REQUIRE REPLACEMENT.

Reported: 2004-03-01 (March 1, 2004) · Model years: 2004

CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE ADVANCED AIR BAG REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE AIR BAG FOR THE FRONT PASSENGER SEAT IS TO BE TURNED OFF (SO THAT IT DOES NOT INFLATE) WHEN CERTAIN OCCUPANTS, SUCH AS SMALL CHILDREN, ARE IN THE FRONT SEAT.

Consequence: THIS REDUCES THE RISK OF SUCH OCCUPANTS BEING UNJURED BY AN INFLATING AIR BAG IN A COLLISION.

Remedy: DEALERS WILL INSPECT THE FRONT PASSENGER SEAT CUSHION/SENSOR ASSEMBLY. IF THE SEAT CUSHION/SENSOR IS FOUND TO BE OPERATING IMPROPERLY, THE SEAT WILL BE REMOVED AND RECALIBRATED. OWNER NOTIFICATION BEGAN ON JUNE 23, 2004. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.

Reported: 2004-04-16 (April 16, 2004) · Model years: 2004

ON CERTAIN MINIVANS EQUIPPED WITH A POWER SLIDING DOOR(S), AT AN AMBIENT TEMPERATURE BELOW APPROXIMATELY 40 DEGREES FAHRENHEIT, THE ACTUATOR FOR THE POWER SLIDING DOOR(S) MAY EXPERIENCE BINDING DUE TO AN OUT-OF-SPECIFICATION CONDITION. IN ORDER TO OPEN, CLOSE OR REVERSE A POWER SLIDING DOOR, THE SHIFT SELECTOR LEVER MUST BE IN "PARK." IF THE ACTUATOR IS EXPERIENCING BINDING AND THE DRIVER SHIFTS THE VEHICLE OUT OF "PARK" WHILE A POWER SLIDING DOOR IS STILL CLOSING, THE DOOR LATCHES MAY NOT ENGAGE.

Consequence: THIS CAN RESULT IN THE DOOR COMING OPEN UNEXPECTEDLY UPON RAPID ACCELERATION, AND AN OCCUPANT COULD FALL OUT OF THE DOOR AND BE INJURED.

Remedy: DEALERS WILL REPLACE THE ACTUATOR FOR THE POWER SLIDING DOOR(S). OWNER NOTIFICATION BEGAN ON JUNE 23, 2004. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.

Reported: 2005-10-13 (October 13, 2005) · Model years: 2004, 2005, 2006

ON CERTAIN MINI VANS, THERE IS A SEAT ADJUSTMENT MECHANISM THAT CONTAINS EXPOSED MOVING COMPONENTS LOCATED AT THE REAR INSIDE EDGE OF THE SECOND ROW SEAT.

Consequence: WHEN THE OPERATOR ATTEMPTS SEAT ADJUSTMENT, A FINGER MAY BE PINCHED IN THE MOVING SEAT ADJUSTMENT MECHANISM WHICH COULD CAUSE AN INJURY.

Remedy: ON EARLIER MODEL VEHICLES BUILT THROUGH JUNE 28, 2004, DEALERS WILL REPLACE THE INBOARD SECOND ROW SEAT ADJUSTMENT HANDLE, RIVET A PLASTIC REINFORCEMENT TO BACKSIDE OF THE EXISTING SEAT BACK COVER CARPETING, INSTALL TIE-DOWNS AND A FLANGE TO THE INBOARD SIDE SHIELD. ON VEHICLES PRODUCED FROM JUNE 29, 2004 THROUGH SEPTEMBER 26, 2005, DEALERS WILL RIVET A PLASTIC REINFORCEMENT TO THE BACKSIDE OF THE EXISTING SEAT BACK COVER CARPETING, INSTALL TIE-DOWNS AND A FLANGE ON THE INBOARD SIDE SHIELD. THE RECALL BEGAN ON DECEMBER 19, 2005. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Reported: 2005-10-17 (October 17, 2005) · Model years: 2004, 2005

ON CERTAIN MINI VANS EQUIPPED WITH A FOLDING THIRD ROW REAR SEAT, WHEN THE THIRD ROW SEAT IS RAISED FROM ITS STOWED POSITION, IT ENGAGES STRIKER BRACKETS, ONE ON EACH SIDE OF THE SEAT CUSHION. THE FOLD-AWAY STRIKER LOOP IS WELDED TO A MOUNTING BRACKET. THE STRIKER MAY BECOME DETACHED FROM ITS MOUNTING BRACKET DUE TO A BROKEN WELD AT THE POINT OF ATTACHMENT TO THE BRACKET.

Consequence: IF THE THIRD ROW SEAT STRIKER WELD FAILS, THE STRIKER COULD SEPARATE FROM THE MOUNTING BRACKET. STRIKER SEPARATION COULD AFFECT THE RISK OF INJURY IN CERTAIN TYPES OF CRASHES.

Remedy: DEALERS WILL REPLACE THE THIRD ROW SEAT STRIKER BRACKETS FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 19, 2005. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Reported: 2007-06-07 (June 7, 2007) · Model years: 2007

DURING PRODUCTION, A SELECT NUMBER OF VEHICLES UNDERWENT AN OFFLINE INSPECTION AT THE ASSEMBLY PLANT WHERE A BOLT IN THE FRONT SUSPENSION ASSEMBLY WAS REMOVED. ON SOME OF THESE VEHICLES, IT IS POSSIBLE THAT THIS BOLT MAY NOT HAVE BEEN TIGHTENED TO SPECIFICATION WHEN IT WAS REINSTALLED.

Consequence: IF THE BOLT IS LOOSE, THE DRIVER WILL HEAR A RATTLING NOISE AND NOTICE VIBRATION. IF THE BOLT COMES OFF COMPLETELY, THE DRIVER CAN EXPERIENCE DIFFICULTY IN CONTROLLING THE DIRECTION OF THE VEHICLE WHICH COULD RESULT IN A CRASH.

Remedy: DEALERS WILL REPLACE THE ATTACHMENT BOLTS AND TIGHTEN THEM TO THE SPECIFIED VALUE. THIS RECALL BEGAN ON JULY 2, 2007. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Reported: 2008-04-24 (April 24, 2008) · Model years: 2008

NISSAN IS RECALLING 1,126 MY 2008 QUEST, TITAN AND ARMADA VEHICLES EQUIPPED WITH MANUAL ADJUSTMENT FRONT SEATS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, "SEATING SYSTEMS." THE SEAT TRACK ASSEMBLY MAY HAVE BEEN MANUFACTURED OUT OF SPECIFICATION.

Consequence: THIS MAY RESULT IN THE MANUAL SEAT PAWL NOT FULLY ENGAGING INCREASING THE RISK OF PERSONAL INJURIES IN THE EVENT OF A CRASH.

Remedy: DEALERS WILL INSPECT THE SEAT TRACK ASSEMBLY ON THE DRIVER'S AND FRONT PASSENGER SEATS AND REPLACE THE ENTIRE SEAT ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON MAY 27, 2008. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Reported: 2010-03-02 (March 2, 2010) · Model years: 2008, 2009

NISSAN IS RECALLING CERTAIN MODEL YEAR 2008-2010 TITAN, ARMADA, AND INFINITI QX56, AND MODEL YEAR 2008-2009 NISSAN QUEST VEHICLES. THE BRAKE PEDAL PIVOT PIN END WAS NOT SPIN-FORMED TO SPECIFICATION DURING THE MANUFACTURING PROCESS OF THE BRAKE PEDAL ASSEMBLY. THE PIVOT PIN COULD SLIDE AND CAUSE THE BRAKE PEDAL TO PARTIALLY DISENGAGE FROM THE BRAKE PEDAL BRACKET.

Consequence: THE DRIVER WILL EXPERIENCE UNUSUAL AND NOTICEABLE LOOSENESS IN THE PEDAL AND A REDUCTION IN BRAKING FORCE INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT TO SEE IF THE PIVOT PIN HAD BEEN FORMED PROPERLY AND WILL REPLACE THE BRAKE PEDAL ASSEMBLY IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 22, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Reported: 2023-02-10 (February 10, 2023) · Model years: 2008, 2009

Nissan North America, Inc. (Nissan) is recalling certain 2008-2011 Titan, Frontier, Xterra, Pathfinder, Armada, and 2008-2009 Quest vehicles. The resin emblem on the driver's air bag cover may develop cracks and detach during air bag deployment.

Consequence: A detached emblem can become a projectile during air bag deployment, increasing the risk of injury to vehicle occupants.

Remedy: Dealers will replace the driver’s airbag cover. Owner letters were mailed December 8, 2023. Owners may contact Nissan's customer service at 1-800-867-7669. Nissan's number for this recall are PC944, PC945, and PC946.

Reported: 2012-02-29 (February 29, 2012) · Model years: 2011, 2012

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011-2012 NISSAN QUEST VEHICLES, MANUFACTURED FROM JULY 29, 2010, THROUGH FEBRUARY 21, 2012. DUE TO SOFTWARE PROGRAMMING, WHILE DRIVING AT SLOW SPEEDS OR IDLING ON A DECLINE WITH ¼ TANK FUEL OR LESS, THERE MAY BE AN INSUFFICIENT SUPPLY OF FUEL TO THE ENGINE. AS A RESULT, THE ENGINE MAY STALL.

Consequence: VEHICLE STALLING COULD INCREASE THE RISK OF A CRASH.

Remedy: NISSAN WILL NOTIFY OWNERS, AND DEALERS WILL REPROGRAM THE FUEL PUMP CONTROL MODULE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT NISSAN CUSTOMER SERVICE AT 1-800-647-7261.