1996 International Harvester 2574: complaints, problems and recalls
Explore the records behind recurring owner reports.
Key facts
0 owner complaints analyzed
2 distinct recall campaigns
Not available median reported failure mileage
Scope: 1996 model year. Data snapshot: . 0 complaints include usable failure mileage.
Most common problems
No owner complaints are recorded for this selection. A complaint can name multiple components.
Component breakdown
Number of unique complaints naming each component. Top eight shown.
No usable records for this chart.
| Category | Count |
|---|
No records.
Reported problems by failure mileage
Complaint counts in mileage bands. These are not failure rates per vehicle or mile.
| Category | Count |
|---|---|
| Under 25,000 | 0 |
| 25,000 to 49,999 | 0 |
| 50,000 to 74,999 | 0 |
| 75,000 to 99,999 | 0 |
| 100,000 to 149,999 | 0 |
| 150,000 and above | 0 |
Under 25,000: 0; 25,000 to 49,999: 0; 50,000 to 74,999: 0; 75,000 to 99,999: 0; 100,000 to 149,999: 0; 150,000 and above: 0
No usable failure mileage is recorded. 0 complaints have missing, zero or invalid mileage.
Complaints over time
Year the complaint was filed, not the vehicle model year or incident year. The snapshot year is partial.
No usable records for this chart.
| Category | Count |
|---|
No records.
Pattern summary
There is not enough complaint evidence to summarize patterns.
Calculated from recorded counts. An AI narrative has not been published for this selection.
Examples from the source records
Examples provide context, not a representative sample or a verified diagnosis.
Recall history
2 distinct campaigns affect this selection. Announcement dates below are different from vehicle model years. A campaign may cover multiple years.
96V124004 · Suspension
Reported: 1996-08-01 (August 1, 1996)
THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD.
Consequence: VEHICLES ARE SUBJECT TO VEHICLE TILT AND POSSIBLE ROLLOVER IN THE EVENT THAT BOTH EQUALIZING BEAMS, ON THE SAME SIDE OF THE VEHICLE, EXPERIENCE A SIMULTANEOUS SHAFT FAILURE. AFFECTED SUSPENSIONS CAN ALSO DROP AND CONTACT THE ROAD SURFACE GENERATING SPARKS WHICH COULD IGNITE FLAMMABLE MATERIAL.
Remedy: OWNER NOTIFICATION IS BEING CONDUCTED BY NEWAY ANCHORLOK. DEALERS WILL INSPECT AND REPLACE ALL SUSPENSION SUSPENSION BEAMS WITH SUSPENSION BEAMS CONTAINING APPROPRIATE SHAFTS.
NHTSA campaign record ↗96V233002 · Suspension:Rear
Reported: 1996-11-22 (November 22, 1996)
THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION.
Consequence: THIS LOCKING TAB PREVENTS THE WHEEL BEARING NUT FROM LOOSENING DURING VEHICLE OPERATION. IF THIS TAB IS DEFORMED, THE NUT CAN LOOSEN ALLOWING THE WHEEL TO SEPARATE FROM THE AXLE INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy: DEALERS WILL REPLACE THE DRIVE AXLE HOUSING NUTS WITH A CONVENTIONAL WHEEL NUT HARDWARE SYSTEM.
NHTSA campaign record ↗