International Harvester 2574 recalls by model year
Explore the records behind recurring owner reports.
Key facts
1 owner complaints analyzed
4 distinct recall campaigns
Not available median reported failure mileage
Scope: 1994 to 2000 model years. Data snapshot: . 0 complaints include usable failure mileage.
Recalls by model year
All campaigns in the snapshot affecting each model year, including recalls announced years later.
Recall campaigns
Shared campaigns appear once in each affected model year.
| Category | Count |
|---|---|
| 1994 | 1 |
| 1995 | 1 |
| 1996 | 2 |
| 1997 | 1 |
| 2000 | 1 |
1994: 1; 1995: 1; 1996: 2; 1997: 1; 2000: 1
Year-by-year records
Recall history
4 distinct campaigns affect this selection. Announcement dates below are different from vehicle model years. A campaign may cover multiple years.
94V196000 · Vehicle Speed Control:Accelerator Pedal
Reported: 1994-10-07 (October 7, 1994) · Model years: 1994, 1995
THE BASE OF THE ELECTRONIC ACCELERATOR PEDAL IS MADE OF DIE CAST ALUMINUM. THE BASE MOUNTS DIRECTLY TO THE CAB FIREWALL. THE CAB FIREWALL IS NOT RIGID ENOUGH OR FLAT ENOUGH AT THE MOUNTING SURFACE, CAUSING STRESS ON THE ACCELERATOR BASE THAT WILL CAUSE THE MOUNTING PADS ON THE BASE OF THE PEDAL ASSEMBLY TO FAIL AND TOTALLY SEPARATE FROM THE FIREWALL.
Consequence: THIS CAN CAUSE LOSS OF SPEED CONTROL, DRIVER DISTRACTION, AND RESULT IN AN ACCIDENT.
Remedy: DEALERS WILL INSPECT THE ACCELERATOR PEDAL ASSEMBLY AND INSTALL A PLATE BETWEEN THE ACCELERATOR MOUNTING BASE AND THE FIREWALL ON THOSE UNITS WHERE THE BASE IS NOT BROKEN AND HAS NO VISIBLE SIGNS OF A CRACK. IF THE BASE IS BROKEN OR CRACKED, THE ACCELERATOR ASSEMBLY WILL BE REPLACED WITH A NEW REDESIGNED ACCELERATOR PEDAL ASSEMBLY.
NHTSA campaign record ↗96V124004 · Suspension
Reported: 1996-08-01 (August 1, 1996) · Model years: 1996
THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD.
Consequence: VEHICLES ARE SUBJECT TO VEHICLE TILT AND POSSIBLE ROLLOVER IN THE EVENT THAT BOTH EQUALIZING BEAMS, ON THE SAME SIDE OF THE VEHICLE, EXPERIENCE A SIMULTANEOUS SHAFT FAILURE. AFFECTED SUSPENSIONS CAN ALSO DROP AND CONTACT THE ROAD SURFACE GENERATING SPARKS WHICH COULD IGNITE FLAMMABLE MATERIAL.
Remedy: OWNER NOTIFICATION IS BEING CONDUCTED BY NEWAY ANCHORLOK. DEALERS WILL INSPECT AND REPLACE ALL SUSPENSION SUSPENSION BEAMS WITH SUSPENSION BEAMS CONTAINING APPROPRIATE SHAFTS.
NHTSA campaign record ↗96V233002 · Suspension:Rear
Reported: 1996-11-22 (November 22, 1996) · Model years: 1996, 1997
THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION.
Consequence: THIS LOCKING TAB PREVENTS THE WHEEL BEARING NUT FROM LOOSENING DURING VEHICLE OPERATION. IF THIS TAB IS DEFORMED, THE NUT CAN LOOSEN ALLOWING THE WHEEL TO SEPARATE FROM THE AXLE INCREASING THE RISK OF A VEHICLE ACCIDENT.
Remedy: DEALERS WILL REPLACE THE DRIVE AXLE HOUSING NUTS WITH A CONVENTIONAL WHEEL NUT HARDWARE SYSTEM.
NHTSA campaign record ↗00V131005 · Power Train:Automatic Transmission
Reported: 2000-06-06 (June 6, 2000) · Model years: 2000
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH EATON AUTOSHIFT GEN II TRANSMISSION ASSEMBLIES. DUE TO A SOFTWARE PROBLEM IN THE TRANSMISSION ASSEMBLIES, THE TRANSMISSION WILL SELECT THE WRONG GEAR.
Consequence: IF AN INAPPROPRIATE GEAR IS SELECTED WITHOUT THE DRIVER'S KNOWLEDGE, THE VEHICLE WILL REACT DIFFERENTLY THAN EXPECTED, POSSIBLY RESULTING IN INJURY OR CRASH.
Remedy: DEALERS WILL REPLACE THE AUTOSHIFT TRANSMISSIONS.
NHTSA campaign record ↗