Lincoln CONTINENTAL recalls by model year

Reported: 1969-04-10 (April 10, 1969) · Model years: 1969

Reported: 1974-01-16 (January 16, 1974) · Model years: 1974

Reported: 1974-08-13 (August 13, 1974) · Model years: 1975

Reported: 1974-09-17 (September 17, 1974) · Model years: 1975

Reported: 1977-09-13 (September 13, 1977) · Model years: 1977

THE INVOLVED VEHICLES WERE FITTED WITH TILT STEERING COLUMNS CONTAINING TRANSMISSION CONTROL INSERTS INTENDED FOR TRUCKS RATHER THAN PASSENGER VEHICLES. THIS MAY CAUSE THE TRANSMISSION SELECTOR POINTER TO BE MISALIGNED AND THE POSSIBILITY OF STARTING THE ENGINE WHEN THE SELECTOR IS BETWEEN THE NEUTRAL (N) AND DRIVE (D) DETENTS AND THE TRANSMISSION IS IN DRIVE.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE TRANSMISSION SHIFT CONTROL INSERT, WITHOUT CHARGE TO OWNER.

Reported: 1978-11-27 (November 27, 1978) · Model years: 1979

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK". AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE PARKING PAWL WITH ONE THAT HAS BEEN HEAT-TREATED.

Reported: 1979-05-15 (May 15, 1979) · Model years: 1979

THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.

Remedy: DEALER WILL REPLACE THE SUSPECT BRAKE RETAINING PIN.

Reported: 1982-04-27 (April 27, 1982) · Model years: 1982

THE INVOLVED VEHICLES MAY HAVE BEEN PRODUCED WITH AN INADEQUATE SEAL BETWEEN THE FUEL FILLER PIPE-HOUSING ASSEMBLY AND THE FUEL FILLER OPENING-COLLAR ASSEMBLY. TWO ATTACHING SCREWS AT THE BOTTOM OF THIS JOINT WERE OMITTED DURING ASSEMBLY. IT IS POSSIBLE THAT A SMALL QUANTITY OF OVERFLOW FUEL COULD LEAK INTO THE RIGHT REAR FENDER WELL BEHIND THE LUGGAGE COMPARTMENT TRIM PANEL IF FUEL "SPIT-BACK" OR OVERFILLING WERE TO OCCUR DURING REFUELING.

Remedy: DEALER WILL INSTALL THE TWO MISSING FASTENERS AND A LOWER FLANGE REINFORCEMENT AT NO COST TO OWNER.

Reported: 1983-02-24 (February 24, 1983) · Model years: 1983

THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.

Remedy: THE DEALER WILL REPLACE THE TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIP AT NO CHARGE TO OWNER.

Reported: 1983-03-07 (March 7, 1983) · Model years: 1983

THE PARKING GEAR MAY NOT ENGAGE, EVEN THOUGH THE GEAR SHIFT LEVER IS PLACED IN THE "PARK" POSITION. THIS OCCURS IF THE LINKAGE INSIDE THE TRANSMISSION THAT ACTUATES THE PARK GEAR WAS IMPROPERLY MANUFACTURED. A PIN THAT RETAINS COMPONENTS ON A LINKAGE (ACTUATING) ROD COULD BREAK AND THE LINKAGE MAY NOT ENGAGE THE PARKING GEAR.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE PARKING PAWL ACTUATING ROD ASSEMBLY.

Reported: 1983-12-20 (December 20, 1983) · Model years: 1984

THE BOLTS THAT ATTACH THE D-SHAPED RING FOR THE SHOULDER BELT ARE INADEQUATELY SUPPORTED BY THE MATERIAL IN WHICH THEY ARE MOUNTED. THE ATTACHMENT DOES NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES".

Remedy: DEALERS WILL INSTALL NEW ATTACHING HARDWARE TO IMPROVE THE STRENGTH OF THE MOUNTING.

Reported: 1984-06-15 (June 15, 1984) · Model years: 1984

IF THE SELECTOR IS GENTLY OR SLOWLY MOVED TOWARDS PARK, THE TRANSMISSION MAY NOT CHANGE TO PARKING GEAR. SIMILARLY, SLOW MOVEMENT OF THE SELECTOR FROM REVERSE TO NEUTRAL MAY NOT REMOVE THE TRANSMISSION FROM REVERSE GEAR.

Remedy: DEALER WILL REPLACE RUBBER-ISOLATED SHIFT ROD WITH A CONVENTIONAL ONE-PIECE ROD AND WILL READJUST THE SHIFT LINKAGE.

Reported: 1985-04-09 (April 9, 1985) · Model years: 1985

A MALFUNCTION MAY OCCUR IN THE AIR SUSPENSION ELECTRICAL CIRCUITRY.

Consequence: A WIRE TO THE AIR SUSPENSION COMPRESSOR COULD OVERHEAT CREATING A POTENTIAL FOR A FIRE, PRIMARILY WHEN PARKED AND KEY IS REMOVED.

Remedy: REPLACE CONTROL MODULE WITH A NEWLY DESIGNED MODULE.

Reported: 1986-08-08 (August 8, 1986) · Model years: 1985, 1986

UNDER CERTAIN CONDITIONS, CONTACTS IN BRAKE SYSTEM RELAY COULD REMAIN CLOSED, CAUSING THE BRAKE PUMP MOTOR TO RUN CONTINUOUSLY, CAUSING IT TO OVERHEAT AND EVENTUALLY FAIL. CONSEQUENCE OF DEFECT: SHOULD THE BRAKE SUPPLY MOTOR FAIL, THE POWER ASSIST TO THE FRONT BRAKES WILL BE LOST, AND AFTER ABOUT 10 TO 15 NORMAL BRAKE STOPS, LOSS OF REAR BRAKE FUNCTION WILL RESULT, CAUSING INCREASED STOPPING DISTANCE. HOWEVER, THE INSTRUMENT BRAKE WARNING LIGHT WILL ILLUMINATE PRIOR TO REDUCED BRAKING CAPABILITY AND IF WARNING IS NOT HEEDED, AN ACCIDENT MAY OCCUR.

Remedy: REPLACE PUMP MOTOR RELAYS.

Reported: 1985-09-19 (September 19, 1985) · Model years: 1986

AN ALUMINUM CASTING FLASH ON THE FACE OF THE THROTTLE BODY MAY BREAK OFF AND BECOME TRAPPED BETWEEN THE THROTTLE PLATE AND THE BORE IN THE THROTTLE BODY. CONSEQUENCES OF DEFECT: THROTTLE MAY FAIL TO RETURN TO IDLE POSITION WHEN RELEASED AND COULD RESULT IN LOSS OF VEHICLE CONTROL WHICH MAY CAUSE AN ACCIDENT.

Remedy: REMOVE EXCESS CASTING FLASH.

Reported: 1986-02-10 (February 10, 1986) · Model years: 1986

WIRING CONNECTIONS IN AN ELECTRICAL CONNECTOR TO THE MASTER CYLINDER RESERVOIR FLUID LEVEL SENSORS WERE REVERSED AND FAIL TO INDICATE LOW FLUID LEVELS AS SPECIFIED BY FMVSS 105, HYDRAULIC BRAKE SYSTEMS. CONSEQUENCE OF DEFECT: SENSOR WILL NOT TRANSMIT SIGNAL TO BRAKE WARNING LIGHT WHEN THE FLUID LEVEL IS LESS THAN ONE FOURTH FULL. WITHOUT THIS WARNING SIGNAL THE FLUID LEVEL MAY DECREASE TO THE POINT WHERE PARTIAL OR COMPLETE LOSS OF BRAKE WOULD BE EXPERIENCED AND MAY LEAD TO AN ACCIDENT.

Remedy: RE-CONFIGURE WIRING TO THE FLUID LEVEL SENSOR CONNECTOR.

Reported: 1986-08-08 (August 8, 1986) · Model years: 1986

THE IGNITION LOCK CYLINDER MAY HANG UP AND NOT FULLY RETURN TO THE "ON" POSITION FROM THE "START" POSITION AFTER STARTING THE ENGINE. IF THIS OCCURS, THE ENGINE WILL REMAIN RUNNING, BUT THE BATTERY CURRENT TO THE BRAKE SYSTEM SUPPLY MOTOR WILL BE INTERRUPTED. CONSEQUENCE OF DEFECT: WITH POWER TO MOST ACCESSORIES AND THE BRAKE SYSTEM SUPPLY MOTOR INTERRUPTED, THE POWER ASSIST TO THE FRONT BRAKE WILL BE LOST AND AFTER ABOUT 10 TO 15 NORMAL BRAKE STOPS, LOSS OF REAR BRAKE FUNCTION WILL RESULT, CAUSING INCREASED STOPPING DISTANCE. HOWEVER, THE INSTRUMENT BRAKE WARNING LIGHT WILL ILLUMINATE PRIOR TO REDUCED BRAKING CAPABILITY AND IF WARNING IS NOT HEEDED, AN ACCIDENT MAY OCCUR.

Remedy: REPLACE IGNITION LOCK CYLINDERS WITH REVISED DESIGN CYLINDERS.

Reported: 1987-09-04 (September 4, 1987) · Model years: 1986, 1987

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Consequence: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

Reported: 1988-03-08 (March 8, 1988) · Model years: 1988

DRIVER AND RIGHT FRONT PASSENGER INBOARD SEAT BELTS MAY BE IMPROPERLY ANCHORED DUE TO LOOSE NUTS THAT COULD BACK OFF.

Consequence: BELT ANCHOR COULD DISENGAGE THE STUD; AN UNATTACHED BELTASSEMBLY WOULD NOT WITHSTAND AN IMPACT LOAD.

Remedy: INBOARD SEAT BELT ANCHORAGES WILL BE CORRECTED TO PREVENT LOOSENING.

Reported: 1988-03-11 (March 11, 1988) · Model years: 1988

TWO TORSION SPRINGS ATTACHED TO REAR SUSPENSION CONTROL ARMS MAY FRACTURE AND RUB AGAINST A REAR TIRE.

Consequence: THIS COULD RESULT IN SUDDEN LOSS OF TIRE INFLATIONPRESSURE WITH POTENTIAL FOR AN ACCIDENT.

Remedy: INSTALL TORSION SPRING SEATS TO RESTRICT THE SPRINGS FROM CONTACTING THE TIRE IF THEY SHOULD FRACTURE.

Reported: 1988-06-27 (June 27, 1988) · Model years: 1988

TRANSMISSION SHIFT CABLES MAY NOT MEET FORDS PULL OUT LOAD SPECIFICATIONS FOR THE SWIVEL TUBE PORTION OF THE CABLE, WHICH COULD ALLOW THE SWIVEL TUBE TO SEPARATE FROM THE SHIFT CABLE ASSEMBLY.

Consequence: OPERATOR WOULD NOT BE ABLE TO SHIFT FROM ONE OF THEDRIVE GEARS INTO PARK POSITION.

Remedy: REPLACE SHIFT CABLE.

Reported: 1988-07-19 (July 19, 1988) · Model years: 1988

NYLON SHIELDED WIRING HARNESS, LOCATED IN THE ENGINE COMPARTMENT, IS SUSCEPTIBLE TO HEAT DAMAGE AND MELTING OF THE NYLON MATERIAL IN 100 DEGREE PLUS WEATHER.

Consequence: MELTED NYLON SHIELD COULD DRIP ONTO THE EXHAUST MANIFOLDAND RESULT IN AN UNDERHOOD FIRE.

Remedy: WRAP WIRING HARNESS WITH HEAT RESISTANT FIBERGLASS TAPE.

Reported: 1988-07-22 (July 22, 1988) · Model years: 1988

ELECTRICAL CIRCUIT THAT CONTROLS CURRENT TO BRAKE PUMP MOTOR RELAY, HEATER AND AIR CONDITIONING BLOWER MOTOR, TURN SIGNALS, AND A ELECTRONIC MESSAGE CENTER MAY OVERHEAT DUE TO INABILITY OF IGNITION CIRCUIT WIRING CONNECTIONS TO DISSIPATE HEAT GENERATED BY ELECTRICAL LOADS.

Consequence: BRAKE PUMP MOTOR WILL NOT OPERATE, SUBSTANTIALLY REDUCINGBRAKING CAPABILITY; BRAKE WARNING LIGHT WILL COME ON.

Remedy: REPLACE IGNITION SWITCH AND MODIFY SWITCH WIRING.

Reported: 1989-04-04 (April 4, 1989) · Model years: 1988

PROCESS USED FOR CONNECTING THE GAS LINES WAS SUBSTANDARD.

Consequence: A GAS LEAK COULD DEVELOP CREATING A FIRE POTENTIAL.

Remedy: INSTALL STANDARD GAS LINE COMPRESSION FITTINGS.

Reported: 1991-08-06 (August 6, 1991) · Model years: 1988, 1989, 1990, 1991

FRONT DISC BRAKE ROTORS OF THE SUBJECT VEHICLES MAY EXPERIENCE SEVERE CORROSION IF OPERATED IN AREAS WHERE CALCIUM CHLORIDE AND SODIUM CHLORIDE ARE USED EXTENSIVELY.

Consequence: SEVERELY CORRODED ROTORS MAY FRACTURE OR SEPARATE NEARTHE INNER EDGES OF THE BRAKE DISCS RESULTING IN REDUCED BRAKING EFFECTIVENESS,HIGHER THAN NORMAL PEDAL EFFORTS, LOUD GRINDING NOISES, AND MODERATE PULLS WHENTHE BRAKES ARE APPLIED. REDUCED BRAKING EFFECTIVENESS MAY INCREASE MINIMUMSTOPPING DISTANCES, POSSIBLY RESULTING IN AN ACCIDENT.

Remedy: REPLACE FRONT BRAKE ROTORS WITH FULL CAST FRONT BRAKE ROTORS.

Reported: 1993-06-23 (June 23, 1993) · Model years: 1988

VEHICLE DESCRIPTION: TAURUS AND SABLES BUILT FROM 10-14-85 THROUGH 8-19-88, AND LINCOLN CONTINENTALS BUILT FROM 11-4-87 THROUGH 9-30-88 (EXCEPT 1989 - 1991 2.5L TAURUS AND 1989 - 1992 SHO). THE AFFECTED CARS WERE ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, AND WISCONSIN. THE BODY MOUNTS AT THE REAR CORNERS OF THE SUBFRAME, WHICH SUPPORTS THE ENGINE AND TRANSMISSION, MAY BECOME DETACHED DUE TO CORROSION OF THE SUBFRAME MOUNT RETAINING PLATE. THIS WOULD ALLOW THE REAR CORNERS OF THE SUBFRAME TO DROP.

Consequence: IF ONE OF THE REAR CORNERS DROPS, ONLY MINOR INDICATIONS OF A MALFUNCTION SUCH AS A CLUNKING NOISE OR SLIGHT CHANGE IN STEERING WHEEL ALIGNMENT ARE NOTICEABLE. HOWEVER, IF BOTH REAR CORNERS OF THE SUBFRAME DROP, STEERING BECOMES VERY DIFFICULT, WHICH COULD ADVERSELY AFFECT VEHICLE CONTROL AND POSSIBLY RESULT IN AN ACCIDENT.

Remedy: INSTALL A CORROSION-RESISTANT REINFORCING PLATE AND A NEW BOLT ON BOTH REAR SUBFRAME MOUNTS. THIS RECALL CAMPAIGN HAS BEEN SUPERSEDED BY RECALL 98V-323.

Reported: 1998-12-16 (December 16, 1998) · Model years: 1988, 1989, 1990, 1991, 1992, 1993, 1994

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, KANSAS, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEBRASKA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, VIRGINIA, WEST VIRGNIA, AND WISCONSIN. THE REAR LOWER SUBFRAME MOUNT PLATE NUT CAN EXPERIENCE STRESS CORROSION CRACKING IF SUBJECTED TO LONG TERM EXPOSURE TO ROAD SALTS. THIS CAN RESULT IN FRACTURE AND LOSS OF THE STRUCTURAL INTEGRITY OF THE SUBFRAME MOUNT ATTACHMENT. DETACHMENT OF THE BODY MOUNTS AT THE REAR CORNERS OF THE SUBFRAME, WHICH SUPPORTS THE ENGINE AND TRANSMISSION, ALLOWS THE REAR CORNERS OF THE SUBFRAME TO DROP.

Consequence: IF BOTH REAR CORNERS DROP, STEERING WOULD BECOME SUDDENLY VERY DIFFICULT, AFFECTING VEHICLE CONTROL AND INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSTALL SUBFRAME REAR MOUNT BOLTS, REINFORCEMENT PLATES, AND PLATE NUTS.

Reported: 1989-03-27 (March 27, 1989) · Model years: 1989

THE LEFT SIDE, REAR SEAT BELT RETRACTOR ASSEMBLY MAY BE IMPROPERLY SECURED AND COULD PULL FREE OF ITS MOUNTING LOCATION.

Consequence: OCCUPANT, THOUGH STILL RESTRAINED BY THE LAP PORTION OFTHE BELT, WOULD NOT HAVE UPPER BODY PROTECTION.

Remedy: REINSTALL THE RETRACTOR ATTACHMENT BOLT.

Reported: 1997-10-07 (October 7, 1997) · Model years: 1989, 1990

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FRONT OUTBOARD SEATING POSITION SEAT BELT BUCKLES MAY NOT LATCH OR UNLATCH.

Consequence: THESE CONDITIONS COULD REDUCE SEAT BELT USAGE INCREASING THE RISK OF PERSONAL INJURY IN THE EVENT OF A VEHICLE CRASH.

Remedy: DEALERS WILL REPLACE THE FRONT OUTBOARD SEAT BELT BUCKLE ASSEMBLIES.

Reported: 1997-02-26 (February 26, 1997) · Model years: 1991, 1992, 1993, 1994

VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH 3.8L ENGINES AND ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: ALASKA, COLORADO, IOWA, IDAHO, ILLINOIS, INDIANA, KANSAS, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, MONTANA, NORTH DAKOTA, NEBRASKA, NEW HAMPSHIRE, NEW YORK, OHIO, PENNSYLVANIA, SOUTH DAKOTA, VERMONT, WISCONSIN, AND WYOMING. WATER CAN ACCUMULATE WITHIN THE SPEED CONTROL CABLE CONDUIT. IF ENOUGH WATER ACCUMULATES, IT COULD FREEZE WITHIN A LOW AREA OF THE CABLE ROUTING WHEN EXPOSED TO A LONG TERM COLD SOAK AT TEMPERATURES AT LEAST SEVERAL DEGREES BELOW FREEZING.

Consequence: DRIVER CONTROL OF VEHICLE SPEED USING THE SPEED CONTROL SYSTEM OR THE ACCELERATOR CONTROL SYSTEM WOULD BE DIMINISHED INCREASING THE RISK OF A VEHICLE CRASH.

Remedy: DEALERS WILL ADD A BOOT TO THE SPEED CONTROL CABLE.

Reported: 1997-02-25 (February 25, 1997) · Model years: 1992, 1993, 1994

THESE VEHICLES ARE ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: ALASKA, IOWA, MINNESOTA, NEBRASKA, NORTH DAKOTA, AND SOUTH DAKOTA. THE VEHICLES INVOLVED ARE 1992-1994 TEMPO/TOPAZ VEHICLES WITH 3.0L ENGINES; 1994 TEMPO/TOPAZ WITH 2.3L ENGINES; 1992-1995 TAURUS/SABLE WITH 3.8L ENGINES; 1994-1995 TAURUS/SABLE WITH 3.0L ENGINES AND 1992-1994 LINCOLN CONTINENTAL VEHICLES WITH 3.8L ENGINES. DURING HIGH WINDS, HEAVY, BLOWING AND DRIFTING SNOW, AND LOW TEMPERATURES, THE ENGINE COOLING FAN CAN BECOME BLOCKED OR FROZEN WITH SNOW. THE FAN MOTOR MAY NOT ROTATE AND COULD OVERHEAT.

Consequence: THIS CONDITION CAN CAUSE SMOKE OR FLAMES FROM THE FAN AND/OR SHROUD, THE FAN ELECTRICAL WIRING, OR THE FAN MOTOR RESULTING IN A VEHICLE FIRE.

Remedy: DEALERS WILL INSTALL AN ELECTRICAL JUMPER HARNESS CONTAINING AN AUTOMATIC RESETTING CIRCUIT BREAKER TO PROTECT THE FAN MOTOR LOW SPEED CIRCUITRY FROM OVERHEATING.

Reported: 1998-01-21 (January 21, 1998) · Model years: 1993, 1994

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE HEADLIGHTS CAN FLASH INTERMITTENTLY AS A RESULT OF THE CIRCUIT BREAKER OPENING. THE VEHICLE'S HEADLIGHTS CAN GO OUT FOR BRIEF INTERVALS.

Consequence: LOSS OF HEADLIGHTS DURING VEHICLE OPERATION CAN AFFECT A DRIVER'S ABILITY TO NAVIGATE THE ROADWAY AND REDUCE THE VISIBILITY OF THE VEHICLE, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSTALL A HEADLIGHT SWITCH THAT INCORPORATES A CRICUIT BREAKER OF REVISED DESIGN AND INSTALLATION OF A WIRING HARNESS CONNECTOR AND WIRING, IF NEEDED.

Reported: 1994-07-12 (July 12, 1994) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER (HAIRPIN CLIP) MAY BE MISSING OR NOT PROPERLY INSTALLED ON THE SERVICE BRAKE PEDAL. THIS CAN CAUSE DISENGAGEMENT OF THE BRAKE PUSHROD AND LOSS OF BRAKING ABILITY.

Consequence: LOSS OF BRAKING ABILITY CAN RESULT IN A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE RETAINER.

Reported: 1996-01-23 (January 23, 1996) · Model years: 1995, 1996

A DEFECTIVE CONTROL MODULE IN THE "AUTOLAMP" SYSTEM CAN MALFUNCTION. IF THE "AUTOLAMP" SYSTEM IS BEING USED TO ACTIVATE THE EXTERIOR LIGHT (INCLUDING HEADLAMPS), THE HEADLAMPS COULD SHUT OFF WITHOUT WARNING. THIS WILL NOT OCCUR IF THE EXTERIOR LIGHTING IS TURNED ON MANUALLY BY THE HEADLIGHT SWITCH.

Consequence: IF THE HEADLAMPS SHUT OFF WHILE THE VEHICLE IS DRIVEN, DRIVER VISIBILITY WOULD BE IMPAIRED INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE "AUTOLAMP" CONTROL MODULE. OWNERS ARE INSTRUCTED TO USE THE MANUAL HEADLAMP SWITCH UNTIL THE CONTROL MODULE CAN BE REPLACED.

Reported: 1996-09-18 (September 18, 1996) · Model years: 1996

THE AUTOMATIC TRANSMISSION PARK PAWL SHAFT MAY NOT BE FREE TO ROTATE AS INTENDED. IF THE PARK PAWL SHAFT DOES NOT ROTATE, IT WOULD PREVENT THE PARK PAWL FROM ENGAGING THE PARK GEAR WHEN THE SHIFT LEVER IS IN THE PARK POSITION.

Consequence: THIS CONDITION COULD RESULT IN THE VEHICLE ROLLING AS IF IN NEUTRAL WITH THE SHIFT LEVER IN THE PARK POSITION.

Remedy: DEALERS WILL INSPECT THE PARK PAWL SHAFT ROTATION AND THOSE SHAFTS WITH RESTRICTED ROTATION WILL BE REPLACED WITH A SHORTER SHAFT THAT WILL NOT RESTRICT ROTATION.

Reported: 1996-09-05 (September 5, 1996) · Model years: 1997

THE PARK PAWL ABUTMENT BRACKET HAS A SHARP EDGE WHICH CAN CAUSE THE PARKING PAWL TO HANG UP AND NOT ENGAGE THE PARK GEAR. THIS WOULD ALLOW THE VEHICLE TO MOVE EVEN THOUGH THE GEAR SHIFT INDICATOR SHOWS THAT THE VEHICLE IS IN PARK.

Consequence: UNINTENDED AND UNEXPECTED VEHICLE MOVEMENT CAN RESULT IN PERSONAL INJURY AND PROPERTY DAMAGE.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE PARK PAWL ABUTMENT BRACKET.

Reported: 1998-02-10 (February 10, 1998) · Model years: 1998

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TEXT AND/OR GRAPHICS FOR THE VEHICLE HEADLAMP AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Consequence: IF THE HEADLAMP ASSEMBLIES ARE REPLACED, CUSTOMERS MAY BE CONFUSED BY THE AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES CAUSING THE HEADLAMPS TO BE IMPROPERLY AIMED.

Remedy: OWNER GUIDES CONTAINING REVISED AIMING INSTRUCTIONS WILL BE MAILED TO OWNERS OF THESE VEHICLES.

Reported: 2003-04-09 (April 9, 2003) · Model years: 1999, 2000

ON CERTAIN PASSENGER VEHICLES, THE DRIVER AND/OR PASSENGER SIDE AIR BAG COULD DEPLOY AS A RESULT OF UNDERBODY IMPACTS NEAR THE SENSORS, SUCH AS THOSE OCCURRING FROM PIECES OF GRAVEL OR DEBRIS THROWN FROM THE WHEELS WHILE THE VEHICLE IS BEING OPERATED AT MODERATE TO HIGH SPEED OR BEING ACCELERATED.

Remedy: DEALERS WILL RECALIBRATE THE AIR BAG SENSORS. OWNER NOTIFICATION BEGAN MARCH 31, 2003. OWNERS MAY CONTACT LINCOLN AT 1-800-521-4140.

Reported: 1998-10-27 (October 27, 1998) · Model years: 1999

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FUEL RAIL CROSSOVER HOSE WAS DAMAGED DURING FUEL RAIL ASSEMBLY ALLOWING FUEL LEAKAGE.

Consequence: FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE CAN RESULT IN FIRE.

Remedy: DEALERS WILL REPLACE THE FUEL RAIL WITH A REVISED FUEL RAIL ASSEMBLY.

Reported: 2001-08-08 (August 8, 2001) · Model years: 2000, 2001

VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE "PARKED" POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.

Consequence: LOSS OF VISIBILITY WHILE DRIVING INCREASES THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON THE WIPER MOTOR. MOTORS BUILT WITH THE SUSPECT TIME FRAME WILL HAVE THE WIPER MOTOR GEAR CASE COVER REPLACED. OWNER NOTIFICATION BEGAN AUGUST 20, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Reported: 1999-09-20 (September 20, 1999) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SEAT BELT RETRACTOR MAY HAVE A PIN SHAFT IN THE SWITCHABLE ELR/ALR MECHANISM THAT IS INCORRECTLY FORMED. IN SOME CIRCUMSTANCES, THE SWITCHING MECHANISM COULD BECOME NONFUNCTIONAL, PREVENTING THE SEAT BELT WEBBING FROM BEING EXTRACTED FROM THE RETRACTOR. IT IS ALSO POSSIBLE THAT MALFUNCTION OF THE MECHANISM COULD PREVENT THE BELT FROM BEING SWITCHED INTO THE ALR MODE. THE ELR MECHANISM IS NOT AFFECTED BY THIS CONDITION.

Consequence: IF THE MECHANISM MALFUNCTIONS AND DOES NOT ALLOW THE WEBBING TO BE EXTRACTED, THE LAP AND SHOULDER BELT COULD NOT BE WORN BY A VEHICLE OCCUPANT. IN THE EVENT THAT THE MECHANISM DOES NOT ALLOW THE ALR MODE TO BE ENGAGED, THE OPERATOR MAY BE UNABLE TO PROPERLY INSTALL A CHILD SEAT IN THAT SEATING POSITION.

Remedy: DEALERS WILL INSPECT THE LAP AND SHOULDER BELT ASSEMBLIES. ASSEMBLIES WITH JULIAN DATE CODES OF 200 THROUGH 223 ARE SUSPECT AND WILL BE REPLACED.

Reported: 2016-10-12 (October 12, 2016) · Model years: 2017

Ford Motor Company (Ford) is recalling certain model year 2017 Lincoln Continental vehicles manufactured June 14, 2016, to September 23, 2016 and equipped with high intensity discharge (HID) headlights. The headlights may have been built with incorrect lenses, adversely affecting the turn signal visibility as well as not being properly marked. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Assoc. Equipment."

Consequence: Reduced turn signal visibility to other drivers and pedestrians can increase the risk of a crash.

Remedy: Ford will notify owners, and dealers will inspect the headlights, replacing them as necessary, free of charge. The recall began November 16, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C15.

Reported: 2017-02-27 (February 27, 2017) · Model years: 2017

Ford Motor Company (Ford) is recalling certain 2016-2017 Ford Edge and Lincoln MKX vehicles and 2017 Lincoln Continental vehicles. In the event of a crash, the driver's frontal air bag may not fully inflate or the air bag cushion may detach from the air bag module. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."

Consequence: During deployment, if the air bag does not fully inflate or the cushion detaches, there is an increased risk of injury in the event of a crash.

Remedy: Ford will notify owners, and dealers will replace the driver frontal air bag module, free of charge. The recall began June 16, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C02.

Reported: 2019-02-11 (February 11, 2019) · Model years: 2017, 2018, 2019

Ford Motor Company (Ford) is recalling certain 2017-2019 Lincoln Continental vehicles. The door latch pawl motors may not function properly, possibly resulting in a door latch not fully engaging.

Consequence: A door latch that is not fully engaged may result in a door opening while driving, increasing the risk of injury.

Remedy: Ford will notify owners, and dealers will replace the latch assemblies on all four doors, free of charge. The recall began October 14, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S03.

Reported: 2022-08-26 (August 26, 2022) · Model years: 2017, 2018, 2019, 2020

Ford Motor Company (Ford) is recalling certain 2017-2020 F-Super Duty F-250, F-350, F-450, and 2017-2020 Lincoln Continental vehicles equipped with the 360-degree camera system. Degradation of the camera's anit-reflective lens coating can lead to a foggy or cloudy rearview camera image.

Consequence: Lack of a clear rearview camera image can reduce the driver's visibility of what is behind the vehicle, increasing the risk of a crash.

Remedy: Dealers will replace the rearview camera, free of charge. Owner notification letters were mailed July 14, 2023. Owners may contact Ford customer service at 1-800-1-866-436-7332. Ford's number for this recall is 22S51.

Reported: 2025-06-27 (June 27, 2025) · Model years: 2019, 2020

Ford Motor Company (Ford) is recalling certain 2018-2022 Transit Connect, 2019-2020 MKZ, MKX, Edge, Continental, F-150, Nautilus, Fusion, 2019-2023 Ranger, Mustang, 2020-2021 EcoSport, Expedition, Navigator, 2020-2022 Escape, F-250 SD, Corsair, 2020-2023 Aviator, Transit, 2020-2024 Explorer, 2021-2024 Bronco Sport, and 2022-2024 Maverick vehicles. A software error may cause the rearview camera to display a blank image, or the image may remain on the display after the backing event has ended.

Consequence: A rearview camera that displays a blank image can reduce the driver's view behind the vehicle. A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver. Both of these situations can increase the risk of a crash.

Remedy: Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed September 4, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S72.