International PROSTAR recalls by model year

Reported: 2008-06-05 (June 5, 2008) · Model years: 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009

NAVISTAR IS RECALLING 51,588 HEAVY TRUCKS, COMMERCIAL BUSES AND SCHOOL BUSES MANUFACTURED BETWEEN NOVEMBER 21, 2000 AND MAY 21, 2008, EQUIPPED WITH ONE OR MORE REMOTE POWER MODULES. THE POTTING MATERIAL THAT ENCAPSULATES THE CIRCUIT BOARD OF THE VEHICLE'S REMOTE POWER MODULE MAY NOT SUFFICIENTLY SEAL THE CIRCUIT BOARD FROM WATER AND CONTAMINATION INTRUSION. IF THE ENCAPSULATION IS COMPROMISED, WATER AND CONTAMINANTS MAY CAUSE AN INTERNAL ELECTRICAL SHORT, POSSIBLY RESULTING IN A FIRE.

Consequence: A FIRE COULD CAUSE PERSONAL INJURY OR DEATH.

Remedy: NAVISTAR WILL NOTIFY OWNERS AND REPAIR THE VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON JULY 10, 2008. OWNERS MAY CONTACT NAVISTAR AT 1-280-461-1890.

Reported: 2007-04-24 (April 24, 2007) · Model years: 2007, 2008

ON CERTAIN TRUCKS, ONE OR BOTH REAR AXLE HOUSINGS MAY CONTAIN THINNER MATERIAL THAN WHAT IS NECESSARY FOR NORMAL VEHICLE OPERATION. OVER TIME, THIS THINNER MATERIAL MAY RESULT IN A FATIGUE FAILURE OF THE REAR AXLE HOUSING, POSSIBLY IN THE LOCATION OF THE BRAKE FLANGE.

Consequence: A CRACK IN THE BRAKE FLANGE LOCATION OF THE REAR AXLE HOUSING MAY RESULT IN A WHEEL END LOCKUP OR WHEEL SEPARATION POSSIBLY RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: DEALERS WILL INSPECT THE VEHICLE'S REAR AXLES AND, IF NECESSARY, REPLACE THE AXLE HOUSINGS. THE RECALL BEGAN ON MAY 18, 2007. OWNERS MAY CONTACT INTERNATIONAL AT 1-800-448-7815.

Reported: 2007-04-24 (April 24, 2007) · Model years: 2007, 2008

ON CERTAIN TRUCKS EQUIPPED WITH DAVCO FUEL PRO 382 HEATED FUEL FILTERS, WHEN THE KEY IS IN THE 'ON' POSITION, THE PRE-HEATER, LOCATED IN THE FUEL FILTER BASE, IS ENERGIZED.

Consequence: IF THIS PRE-HEATER IS ENERGIZED WHILE MAINTENANCE IS BEING PERFORMED ON THE FUEL FILTER, DIESEL FUEL COULD IGNITE WITHIN THE FILTER HOUSING. A FIRE WITHIN THE FUEL FILTER HOUSING MAY SPREAD POSSIBLY RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY.

Remedy: DEALERS WILL INSPECT THE FUEL FILTERS AND FUEL HEATERS AND, IF NECESSARY, WILL REPLACE THE FUEL HEATER. THE RECALL BEGAN ON MAY 11, 2007. OWNERS MAY CONTACT INTERNATIONAL AT 1-800-448-7825.

Reported: 2008-01-28 (January 28, 2008) · Model years: 2008

ON CERTAIN TRUCKS, THE RETENTION SYSTEM OF THE PIN THAT ATTACHES THE HOOD TRAVEL LIMITING SHOCK TO THE MOUNTING BRACKET ON TOP OF THE RADIATOR MAY BECOME DISABLED DUE TO INTERFERENCE BETWEEN IT AND THE GRAB HANDLE POCKET OF THE HOOD. THIS COULD ALLOW THE PIN TO WORK OUT OF THE CONNECTION RESULTING IN THE HOOD SEPARATING FROM THE SHOCK.

Consequence: WITH THE VEHICLE IN A STATIONARY POSITION, THIS CONDITION MAY CAUSE A SITUATION WHERE THE INDIVIDUAL OPENING THE HOOD WOULD HAVE TO MANUALLY SUPPORT THE WEIGHT OF THE HOOD WITHOUT WARNING WHICH COULD RESULT IN PERSONAL INJURY.

Remedy: DEALERS WILL REPLACE THE HOOD/HOOD TRAVEL LIMITING SHOCK CONNECTION PIN AND PIN RETENTION SYSTEM WITH A SYSTEM THAT DOES NOT INTERFERE WITH THE HOOD GRAB HANDLE POCKET. THE RECALL BEGAN ON APRIL 11, 2008. OWNERS MAY CONTACT INTERNATIONAL AT 1-800-448-7825.

Reported: 2008-02-29 (February 29, 2008) · Model years: 2008, 2009

INTERNATIONAL IS RECALLING MY 2008-2009 4000, 5000, 7000, 8000, 9000 AND PROSTAR TRACTOR/TRUCKS EQUIPPED WITH BENDIX MV-3 DASH CONTROL VALVES. THE MOLDED VALVE BODY HAS AN INCORRECT CORE PIN IN THE INJECTION MOLD CAUSING THE VALVE BODY TO BE OVERSIZED IN THE DOUBLE CHECK VALVE AREA. THIS CONDITION CAN ALLOW THE RUBBER DOUBLE CHECK VALVE TO BECOME LODGED IN THE BODY OPENING UNDER CERTAIN CIRCUMSTANCES.

Consequence: IF THE DOUBLE CHECK VALVE BECOMES LODGED, IN THE EVENT OF A PRIMARY RESERVOIR FAILURE, AIR PRESSURE CAN LEAK PAST THE LODGED DOUBLE CHECK VALVE THEREBY DEPLETING THE SECONDARY RESERVOIR, CAUSING REDUCED ABILITY FOR MODULATING THE SERVICE EMERGENCY BRAKES INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE BENDIX MV-3 DASH CONTROL VALVES FREE OF CHARGE. THE RECALL BEGAN ON MAY 9, 2008. OWNERS MAY CONTACT INTERNATIONAL AT 1-800-448-7825.

Reported: 2008-11-24 (November 24, 2008) · Model years: 2008, 2009, 2010

NAVISTAR IS RECALLING 14,048 MY 2008-2010 LONESTAR AND PROSTAR TRUCKS. THE SERVICE BRAKE AIR LINE THAT RUNS FROM THE TRACTOR PROTECTION VALVE TO THE FAST BRAKE MODULE MAY SEPARATE FROM THE FAST BRAKE MODULE RESULTING IN LOSS OF TRAILER SERVICE BRAKES.

Consequence: LOSS OF TRAILER SERVICE BRAKES MAY CAUSE A CRASH RESULTING IN POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: DEALERS WILL REPLACE THE FAST BRAKE MODULES AND THE AIR LINES RUNNING TO THE MODULE WILL BE REROUTED TO ELIMINATE LINE TENSION CAUSED BY CAB TO FRAME RELATIVE MOTION. THE RECALL BEGAN ON MARCH 20, 2009. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2010-08-24 (August 24, 2010) · Model years: 2008, 2009, 2010, 2011

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 INTERNATIONAL PROSTAR AND LONESTAR HEAVY TRUCKS MANUFACTURED FROM JANUARY 2, 2007 THROUGH JUNE 1, 2010. THE PASSENGER SIDE WINDSHIELD WIPER LINKAGE ROD MAY SEPARATE FROM EITHER THE WIPER DRIVE ARM OR PASSENGER SIDE PIVOT ASSEMBLY.

Consequence: WHEN THE LINKAGE SEPARATES, THE PASSENGER SIDE WIPER ARM WILL NO LONGER OPERATE WHICH COULD LEAD TO REDUCED DRIVER VISIBILITY, INCREASING THE RISK OF A CRASH.

Remedy: NAVISTAR WILL NOTIFY OWNERS AND INTERNATIONAL DEALERS WILL REPLACE THE WINDSHIELD WIPER LINKAGE ASSEMBLY FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 17, 2010. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2013-09-18 (September 18, 2013) · Model years: 2008, 2009, 2010, 2011, 2012, 2013

Navistar, Inc. is recalling certain model year 2008-2013 International LoneStar, ProStar, and TranStar trucks manufactured February 20, 2008, through July 29, 2013 and equipped with an electronic fifth wheel jaw release system (feature code 0595BAW or 0595BAY). Due to an assembly error, the air lines at the isolation/vent valve may not be oriented correctly.

Consequence: Because of the improper orientation, in the event of an air leakage at the isolation/vent valve, the 5th wheel jaw may release, unexpectedly releasing the trailer from the tractor, increasing the risk of a vehicle crash.

Remedy: Navistar will notify owners, and dealers will inspect the air line routing. If necessary, the air line routing will be corrected free of charge. The recall began on October 10, 2013. Owners may contact Navistar at 1-331-332-1590. Navistar's recall number is 13514.

Reported: 2023-05-18 (May 18, 2023) · Model years: 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018

Navistar, Inc. (Navistar) is recalling certain 2000-2003 International 8100, 2001-2003 International 9100i, 2001-2007 International 9400i, 2001-2010 International 9200i, 2002-2007, 2009 International 8500, 2003-2007, 2013 International 9900i, 2003-2018 International 8600, 2004, 2007 International 9900iX, 2008-2018 International ProStar, 2010-2011, 2013, 2016 International LoneStar, 2011-2012, 2016 International 4400, 2017-2024 International LT, 2018-2024 International RH, 2019-2021 International LS, 2019-2024 International MV vehicles. The back-up lights offer low visibility when the vehicle is in reverse and bobtail mode. Also, the vehicles have not been equipped with additional unobstructed back-up lights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Consequence: Low visibility or obstructed back up lights may not alert other drivers that the vehicle is backing up, increasing the risk of a crash.

Remedy: Dealers will replace the existing rear stop/turn signal lights, free of charge. Owner notification letters were mailed May 06, 2024. Owners may contact Navistar's customer service at 1-800-448-7825. Navistar's number for this recall is 23514.

Reported: 2010-02-03 (February 3, 2010) · Model years: 2009, 2010

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2009-2010 INTERNATIONAL PROSTAR AND LONESTAR TRUCKS EQUIPPED WITH FEATURE CODE 04AZT ROLL STABILITY CONTROL. THE AIR LINE THAT SUPPLIES THE TRACTION SOLENOID VALVE OF THE ROLL STABILITY CONTROL (RSC) SYSTEM MAY HAVE BEEN CONNECTED TO AN INCORRECT PORT ON THE AIR TANK. THIS CONDITION WILL AFFECT AIR MODULATION TO THE TRAILER BRAKES IF RSC IS ACTIVATED DURING A ROLL STABILITY EVENT. THIS CONDITION AT NO TIME AFFECTS THE NORMAL DESIGN FUNCTION OF THE TRACTOR AND TRAILER SERVICE BRAKES WHEN ACTIVATED BY THE DRIVER, OR THE FUNCTION OF THE TRACTOR RSC SYSTEM.

Consequence: LESS THAN OPTIMAL RSC CONTROL OF THE TRAILER BRAKES DURING A ROLL STABILITY EVENT MAY INCREASE THE RISK OF A CRASH WHICH CAN RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: DEALERS WILL INSPECT AND RELOCATE THE AIR LINE THAT SUPPLIES THE RSC TRACTION SOLENOID VALVE TO THE CORRECT PORT ON THE AIR TANK. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 19, 2010. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2010-03-18 (March 18, 2010) · Model years: 2009, 2010, 2011

NAVISTAR HAS NOTIFIED NHTSA OF A DEFECT ON CERTAIN MODEL YEAR 2008-2011 INTERNATIONAL TRUCKS EQUIPPED WITH AN OPTIONAL JUMP START STUD. CORROSION AT THE BASE OF THE STUD MAY CAUSE AN ELECTRICAL SHORT BETWEEN THE STUD AND BATTERY BOX.

Consequence: AN ELECTRICAL SHORT MAY CAUSE A VEHICLE FIRE.

Remedy: A FINAL REMEDY HAS BEEN ESTABLISHED. NAVISTAR WILL NOTIFY OWNERS, AND DEALERS WILL REPAIR THE VEHICLES BY INSTALLING A NEW JUMP START STUD. REPAIRS WILL BE PREFORMED FREE OF CHARGE. AN INTERIM ACTION WILL INVOLVE THE REMOVAL OF THE JUMP START STUD AND THE CONNECTING CABLE. THE SAFETY RECALL BEGAN ON SEPTEMBER 10, 2010. OWNERS MAY CONTACT INTERNATIONAL DEALERS AT 1-800-448-7825.

Reported: 2014-10-31 (October 31, 2014) · Model years: 2009, 2010, 2011, 2012, 2013, 2014, 2015

Navistar, Inc. (Navistar) is recalling certain model year 2010-2015 International Lonestar vehicles manufactured October 12, 2009, to June 16, 2014, and 2009-2015 International ProStar vehicles manufactured December 16, 2008, to June 20, 2014. In the affected vehicles the electrical harness that supplies power to the HVAC system may not be of sufficient size for the electrical load of the circuit. This can result in an increase in resistance and heating at the connectors.

Consequence: An increase in resistance and heating at the connectors could cause a vehicle fire.

Remedy: Navistar will notify owners, and dealers will replace the 60 amp relay and battery harness with a 150 amp relay and battery harness, free of charge. Navistar issued an interim notification to owners on December 29, 2014. The recall began on March 2, 2015. Owners may contact Navistar customer service at 1-331-332-1590. Navistar's number for this recall is 14516.

Reported: 2010-06-14 (June 14, 2010) · Model years: 2010, 2011

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010 AND 2011 INTERNATIONAL 4300M, 8600, LONESTAR AND PROSTAR BRAND TRUCKS MANUFACTURED FROM MAY 6, 2009 THROUGH MAY 25, 2010. THE FASTENER THAT CLAMPS THE PITMAN ARM TO THE STEERING GEAR SHAFT MAY HAVE BEEN UNDERTORQUED UPON ASSEMBLY. AN UNDER TORQUE CONDITION MAY CAUSE WEAR OF THE INTERCONNECTING SPLINES OF THE ARM AND THE SHAFT POSSIBLY ALLOWING THE PITMAN ARM TO SLIP OVER THE SHAFT RESULTING IN A REDUCTION OF STEERING CONTROL.

Consequence: A REDUCTION OF STEERING CONTROL INCREASES THE RISK OF A CRASH.

Remedy: NAVISTAR WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 9, 2010. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2011-08-17 (August 17, 2011) · Model years: 2010, 2011, 2012

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010-2012 PAYSTAR, WORKSTAR, TRANSTAR, AND PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM JUNE 1, 2009, THROUGH MAY 31, 2011, EQUIPPED WITH A MAXXFORCE 11 OR 13 ENGINE (FEATURE CODE 12UXJ OR 12UXH) AND WITH ALTERNATOR FEATURE CODE 08GGN, 08GGR, 08 GHG, OR 08GHH. THE ALTERNATOR CABLE MAY RUB ON THE HIGH PRESSURE POWER STEERING HOSE, POSSIBLY CHAFING ITS INSULATION AND CAUSING AN ELECTRICAL SHORT.

Consequence: AN ELECTRICAL SHORT MAY CAUSE A VEHICLE FIRE POSSIBLY RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: NAVISTAR WILL INSTALL A BRACKET TO ROUTE THE WIRES AWAY FROM THE POWER STEERING HOSE. NAVISTAR DID NOT PROVIDE AN EXPECTED START DATE FOR THE RECALL, BUT AN INTERIM NOTICE WILL BE MAILED TO OWNERS IF PARTS WILL NOT BE AVAILABLE UNTIL AFTER OCTOBER 14, 2011. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825. THIS RECALL CAMPAIGN HAS BEEN SUPERSEDED BY 12V-196.

Reported: 2012-05-02 (May 2, 2012) · Model years: 2010, 2011, 2012, 2013

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2010 THROUGH 2013 PAYSTAR, WORKSTAR, TRANSTAR, AND PROSTAR, AND MODEL YEAR 2012 AND 2013 LONESTAR COMMERCIAL TRUCKS MANUFACTURED FROM JUNE 1, 2009, THROUGH APRIL 4, 2012, EQUIPPED WITH A MAXXFORCE 11 OR 13 ENGINE (FEATURE CODE 12UXJ OR 12UXH) AND WITH BOSCH ALTERNATOR FEATURE CODES 08GGN, 08GGR, 08GHG, OR 08GHH. THE ALTERNATOR CABLE MAY RUB ON THE HIGH PRESSURE POWER STEERING HOSE, POSSIBLY CHAFING ITS INSULATION AND CAUSING AN ELECTRICAL SHORT.

Consequence: AN ELECTRICAL SHORT MAY CAUSE A VEHICLE FIRE POSSIBLY RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: NAVISTAR WILL INSTALL A STANDOFF BRACKET AND IMPROVE HARNESS ROUTING TO BETTER ROUTE THE ALTERNATOR WIRES AWAY FROM THE POWER STEERING HOSE. THE SAFETY RECALL BEGAN ON JULY 16, 2012. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2010-12-20 (December 20, 2010) · Model years: 2011

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2011 INTERNATIONAL PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM SEPTEMBER 22, 2010, THROUGH DECEMBER 3, 2010, EQUIPPED WITH DRIVELINE FEATURE CODE 06WAK. THE RUBBER ISOLATOR MATERIAL THAT HOLDS THE DRIVELINE CENTER BEARING IN THE MOUNTING BRACKET MAY DETERIORATE DUE TO AN INCORRECT MOUNTING LOCATION POSSIBLY RESULTING IN DRIVELINE SEPARATION WITHOUT WARNING.

Consequence: DRIVELINE SEPARATION MAY CAUSE A CRASH POSSIBLY RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: NAVISTAR WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE CENTER BEARING AND ITS MOUNTING HARDWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 27, 2011. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2011-04-19 (April 19, 2011) · Model years: 2011, 2012

NAVISTAR IS RECALL CERTAIN MODEL YEAR 2011 AND 2012 INTERNATIONAL DURASTAR, PAYSTAR, WORKSTAR, TRANSTAR, LONESTAR AND PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM NOVEMBER 5, 2010, THROUGH MARCH 10, 2011, FOR FAILING TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS (ABS)." THE TRAILER ABS FAULT INDICATOR LAMP IN THE INSTRUMENT CLUSTER WILL NOT ILLUMINATE DUE TO A PROGRAMMING OR HARDWARE ISSUE WITH THE BRAKE SYSTEM ELECTRONIC CONTROL UNIT.

Consequence: AN INOPERABLE TRAILER ABS FAULT INDICATOR MAY PREVENT THE DRIVER FROM BEING AWARE OF A TRAILER ABS FAULT CONDITION THEREBY POSSIBLY INCREASING THE RISK OF A CRASH POTENTIALLY RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: NAVISTAR WILL NOTIFY OWNERS. DEALERS WILL REPROGRAM OR REPLACE THE BRAKE SYSTEM ELECTRONIC CONTROL UNIT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 12, 2011. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2012-02-13 (February 13, 2012) · Model years: 2011, 2012, 2013

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2012-2013 IC BUS CE-C, HC, AND INTERNATIONAL 9400 AND CERTAIN MODEL YEAR 2011 THROUGH 2013 INTERNATIONAL DURASTAR, PAYSTAR, WORKSTAR, TRANSTAR, LONESTAR, PROSTAR, 9200, AND 9800, AND CERTAIN MODEL YEAR 2013 INTERNATIONAL 9900, VEHICLES, MANUFACTURED FROM DECEMBER 2, 2010, THROUGH JANUARY 26, 2012, AND EQUIPPED WITH BENDIX ATR-6 TRACTION RELAY VALVES. IN EXTREMELY COLD CONDITIONS, THESE BENDIX RELAY VALVES MAY POTENTIALLY DEVELOP INTERNAL LEAKAGE. INTERNAL LEAKAGE CAN LEAD TO AIR PRESSURE BEING DELIVERED TO AFFECTED PRIMARY OR SECONDARY BRAKES CAUSING CONTINUOUS BRAKE APPLICATION.

Consequence: UNEXPECTED CONTINUOUS BRAKE APPLICATION CAN CAUSE THE BRAKES TO OVERHEAT AND LEAD TO A FIRE. UNEXPECTED CONTINUOUS BRAKE APPLICATION CAN CAUSE THE DRIVER TO LOSE CONTROL OF THE VEHICLE, INCREASING THE RISK OF A CRASH. ALSO, THE BRAKES MAY BE APPLIED WITHOUT ILLUMINATING THE BRAKE LIGHTS, FAILING TO GIVE PROPER WARNING TO OTHER DRIVERS.

Remedy: NAVISTAR WILL NOTIFY OWNERS, AND DEALERS WILL PROVIDE A TEMPORARY REPAIR UNTIL BENDIX DEVELOPS A PERMANENT REMEDY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 10, 2012. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2012-09-20 (September 20, 2012) · Model years: 2011, 2012, 2013

Navistar is recalling certain model year 2013 International 8600, 2012 and 2013 Durastar, 2011-2013 ProStar, and 2012 WorkStar trucks, manufactured from November 23, 2010, through April 02, 2012, and equipped with piston spring brake feature code 04EVP. The piston bore area of the parking brake chamber may have an air leak could result in the parking brake not fully releasing.

Consequence: If the parking brake does not fully release, the service brakes may lock up without warning, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace the spring brake chamber free of charge. The safety recall began on November 6, 2012. Owners may contact Navistar at 1-331-332-1590.

Reported: 2013-04-17 (April 17, 2013) · Model years: 2011, 2012, 2013

Navistar is recalling certain model year 2011-2012 International Lonestar, model year 2012-2013 International Terrastar and model year 2011-2013 International DuraStar, ProStar, TranStar, and WorkStar commercial trucks manufactured from June 1, 2010, through March 7, 2012 and equipped with day cab codes 16CAB, 16030, or 16196 and feature codes 16WCE, 16WCR, 16XWD, 16XWE, 16XWV, 16XXB, 16XXD, 16XXE, 16XXG, or 16XYN sun shades. The sun shade may not be properly secured to the cab roof panel which may result in partial or full separation of the sun shade from the roof panel.

Consequence: If the sun shade separates from the cab roof during vehicle operation, the sudden release of the sun shade could distract the driver increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will inspect and strengthen the sun shade mounting, free of charge. The safety recall began on September 10, 2013. Owners may contact Navistar at 1-800-448-7825. Navistar's campaign number is 13505.

Reported: 2015-04-22 (April 22, 2015) · Model years: 2011, 2012, 2013, 2014, 2015

Navistar, Inc. (Navistar) is recalling certain model year 2011-2015 International DuraStar, ProStar, TranStar and WorkStar, 2012-2015 International TerraStar, 2013-2015 International LoneStar and IC Bus HC, and 2014-2015 IC Bus AC vehicles. A vehicle double battery jump start or electrical load dump event could result in an overvoltage condition of a component within the HVAC system linear power module (LPM) which is used to control the blower speed. The overvoltage condition could result in the overheating and failure of the LPM.

Consequence: If the LPM overheats and fails, there is an increased risk of a fire.

Remedy: Navistar will notify owners, and dealers will replace the LPM with an upgraded one, free of charge. An interim letter was mailed to owners on June 18, 2015. A second notification will mailed when parts become available. The recall began on August 6, 2015. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 15509.

Reported: 2015-09-29 (September 29, 2015) · Model years: 2011, 2012, 2013, 2014

Navistar, Inc. (Navistar) is recalling certain model year 2011-2014 International ProStar trucks manufactured May 18, 2010, to April 5, 2013, 2012-2014 International LoneStar trucks manufactured September 7, 2011, to March 25, 2013, and 2011-2013 International TranStar trucks manufactured October 18, 2010, to February 20, 2013. The affected trucks are equipped with Fontaine Ultra LT Fifth Wheel connectors, which, due to cumulative damage to the fifth wheel and its locking mechanism, have a locking mechanism that may fail to operate or to properly engage.

Consequence: If the fifth wheel and locking mechanism are sufficiently damaged, the locking mechanism may fail to operate as intended and the trailer may unexpectedly detach from the tractor, increasing the risk of a crash.

Remedy: Navistar will notify owners, and Fontaine dealers will replace the fifth wheel with an Ultra NT model fifth wheel, free of charge. The recall began on November 18, 2015. Owners may contact Navistar customer service at 1-800-448-7825, or Fontaine customer service at 1-844-597-7393.

Reported: 2011-12-19 (December 19, 2011) · Model years: 2012

NAVISTAR IS RECALLING CERTAIN 2012 INTERNATIONAL PROSTAR COMMERCIAL TRUCKS MANUFACTURED FROM MARCH 22, 2011, THROUGH DECEMBER 9, 2011, EQUIPPED WITH FEATURE CODE 04AZX MERITOR WABCO ELECTRONIC STABILITY CONTROL (ESC) UNITS. UNDER CERTAIN ROAD AND DRIVING CONDITIONS, VEHICLE BODY ROLL AND ROAD INCLINATION CHARACTERISTICS MAY ADVERSELY AFFECT THE SLIP ANGLE CALCULATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM. THIS MIGHT CAUSE THE ESC TO PERCEIVE AN OVER STEERING SITUATION AND THEREFORE APPLY THE OUTER WHEEL BRAKE ON THE FRONT AXLE UNTIL THE VEHICLE IS PERCEIVED TO BE STABLE.

Consequence: IF THE DRIVER IS SLOW TO REACT DURING THIS ESC INTERVENTION, THE VEHICLE MAY DEVIATE FROM THE INTENDED LINE OF TRAVEL, INCREASING THE RISK OF A CRASH.

Remedy: NAVISTAR WILL NOTIFY OWNERS, AND DEALERS WILL INSTALL A NEW ESC MODULE FREE OF CHARGE. THE SAFETY RECALL BEGAN DURING FEBRUARY 2012. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2012-03-22 (March 22, 2012) · Model years: 2012

NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2012 INTERNATIONAL LONESTAR AND PROSTAR TRUCKS, MANUFACTURED FROM MARCH 24, 2011, THROUGH NOVEMBER 22, 2011, EQUIPPED WITH a FEATURE CODE 08VTS, 08JAU, OR 08JAW BATTERY BOX. THE MOUNTING BRACKETS USED TO INSTALL THE BATTERY BOX LOWER STEP WERE ASSEMBLED WITH TWO WELDS INSTEAD OF THREE WELDS AND MAY CAUSE THE STEP MOUNT TO BREAK OFF FROM THE BRACKET.

Consequence: A FAILURE OF THE STEP MOUNTING BRACKET MAY CAUSE THE STEP TO UNEXPECTEDLY BREAK OFF WHICH CAN RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: NAVISTAR WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE BOTH STEP MOUNTING BRACKETS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 6, 2012. OWNERS MAY CONTACT NAVISTAR AT 1-800-448-7825.

Reported: 2012-08-14 (August 14, 2012) · Model years: 2012, 2013

Navistar is recalling certain model year 2011-2013 International vehicles manufactured from November 2, 2010 through May 25, 2012, equipped with Bendix air disc brakes. Bolts that fasten the air disc brake caliper to the caliper mounting plate may not have been tightended to their specified torque. This may cause the mouting bolts to become loose and possibly allow the air disc brake caliper to separate from the caliper mounting plate, resulting in an unexpected pull condition during braking application or an unexpected increase in stopping distance.

Consequence: An unexpected pull condition during braking application or an unexpected increase in stopping distance, increases the risk of a crash, leading to property damage, personal injury, or death.

Remedy: Navistar will notify owners, and dealers will replace any missing caliper mounting bolts and tighten caliper mounting bolts, free of charge. The safety recall began on October 30, 2012. Owners may contact Navistar at 1-331-332-1590.

Reported: 2012-11-21 (November 21, 2012) · Model years: 2012, 2013

Navistar is recalling certain model year 2012-2013 International brand ProStar and TranStar commercial trucks, manufactured from August 01, 2011, through June 12, 2012, and equipped with front brake linings listed as feature codes 0504501 or 0504504. The brake S-Cam tube bracket assemblies on the steer axles may fracture.

Consequence: Brake assembly fractures may result in an inoperative brake on the affected wheel. This will cause the vehicle to pull to one side unexpectedly during breaking and/or increase the stopping distance. Either result may increase the risk of a vehicle crash.

Remedy: Navistar will notify owners, and dealers will replace S-Cam tube bracket assemblies free of charge. The safety recall is expected to begin by August 23, 2013. Owners may contact Navistar at 1-800-448-7825.

Reported: 2013-06-04 (June 4, 2013) · Model years: 2012, 2013

Navistar is recalling certain model year 2012-2013 International brand ProStar and TranStar commercial trucks, manufactured from August 01, 2011, through July 10, 2012, and equipped with front brake linings listed as feature codes 0504501, 0504504, or 04EWM. The brake S-Cam tube bracket assemblies on the steer axles may fracture.

Consequence: Brake assembly fractures may result in an inoperative brake on the affected wheel. This will cause the vehicle to pull to one side unexpectedly during breaking and/or increase the stopping distance. Either result may increase the risk of a vehicle crash.

Remedy: Navistar has already notified all affected owners about the defect during the course of the 2012 campaign that did not launch due to parts delays. The remedy began on September 12, 2013. Dealers will replace the S-Cam tube bracket assemblies, free of charge. Owners may contact Navistar at 1-800-448-7825. Navistar's number for this recall is 12530. This recall supersedes recall 12V-546.

Reported: 2014-02-20 (February 20, 2014) · Model years: 2012, 2013

Navistar Inc., is recalling certain model year 2012-2013 International Lonestar, Paystar, Prostar, Workstar and 9900 trucks, equipped with feature code 0504501, 0504504, or 04EWM Reduced Stopping Distance (RSD) brake linings and with or without feature code 04WCS Greased For Life front air S-cam brakes. In the affected vehicles, the brake S-cam brackets may fracture.

Consequence: S-cam bracket fractures may result in an inoperative brake on the affected wheel. This will cause the vehicle to pull to one side unexpectedly during braking and/or increase the stopping distance. Either result may increase the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace the S-cam brake assemblies with a brake assembly with cast spiders and S-cam tube bracket assemblies with reinforced gussets, free of charge. The recall began on March 27, 2014. Owners may contact Navistar at 1-331-332-1590. Navistar's number for this recall 14501. Note: This recall is an expansion of recall 13V231.

Reported: 2017-12-11 (December 11, 2017) · Model years: 2012, 2014, 2015, 2016, 2017

Navistar, Inc. (Navistar) is recalling certain 2000-2001 International 4700, 2000-2002 4900, 2001-2003 8100 (TranStar) and 9100I, 2002-2003, 2005, 2007-2009, 2012-2014 and 2016-2018 DuraStar, 2012 and 2014-2017 ProStar, 2014-2015 TerraStar, and 2018 LT trucks. These vehicles are equipped with Kidde Plastic-Handle or Push Button 'Pindicator' fire extinguishers that may become clogged, preventing the extinguisher from discharging as expected or excessive force may be needed to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

Remedy: Navistar will notify owners, instructing them to notify Kidde for a replacement fire extinguisher, free of charge. The recall is expected to begin February 9, 2018. Owners may contact Navistar customer service at 1-331-332-1590, or contact Kidde customer service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information.

Reported: 2012-10-17 (October 17, 2012) · Model years: 2013

Navistar is recalling certain model year 2013 International brand LoneStar, ProStar, and WorkStar commercial trucks, manufactured from April 22, 2012, through October 29, 2012, and equipped with steering wheel feature codes 05CAW, 05CAX, 05CAZ, 05CBA, or 05WBD. The steering wheel may not have been completely welded to its mounting hub.

Consequence: A steering wheel with an incomplete weld may separate from the steering wheel mounting hub, leading to a loss of vehicle control and increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will inspect and replace affected steering wheels, free of charge. The safety recall began on November 21, 2012. Owners may contact Navistar at 1-800-448-7825.

Reported: 2012-10-18 (October 18, 2012) · Model years: 2013

Navistar is recalling certain model year 2013 International ProStar commercial trucks, manufactured from May 14, 2012, through August 14, 2012, and equipped with tow hook feature code 01570. The tow hooks may not have been heat treated to specification resulting in reduced strength.

Consequence: Improperly heat treated tow hooks may unexpectedly break during vehicle recovery, resulting in the towed vehicle separating from the towing vehicle while in traffic, increasing the risk of a crash without warning with accompanying vehicle damage, injuries or deaths.

Remedy: Navistar will notify owners, and dealers will replace the suspect tow hooks, free of change. The safety recall ibegan on December 18, 2012. Owners may contact Navistar at 1-800-448-7825.

Reported: 2013-03-20 (March 20, 2013) · Model years: 2013

Navistar is recalling certain model year 2013 International ProStar commercial trucks, manufactured from January 24, 2012, through January 2, 2013, with feature codes 29AEB and 29AEC (Preset Plus hubs). The axle bearing retaining nut lock snap ring may have not been installed or may have been installed incorrectly which may result in the retainer nut working loose and possibly separating the wheel hub from the axle.

Consequence: Separation of a wheel hub from an axle may increase the risk of a crash.

Remedy: Navistar will notify owners, and dealers will inspect and replace any missing axle bearing retainer nut lock snap rings, free of charge. The safety recall began on April 24, 2013. Owners may contact Navistar at 1-800-448-7825.

Reported: 2013-11-20 (November 20, 2013) · Model years: 2013, 2014

Navistar, Inc. is recalling certain model year 2013-2014 International ProStar sleeper cab vehicles manufactured December 12, 2012, through August 8, 2013 and equipped with feature code 16XSA, 16XSB, 16XSC or 16XSD chassis skirts. In the affected vehicles, the rear chassis skirt upper horizontal support S-bracket may rub the fuel tank causing a hole in the tank.

Consequence: A hole in the tank would allow fuel to leak onto the roadway causing dangerous driving conditions, which could result in a vehicle crash, property damage, personal injury, or death.

Remedy: Navistar will notify owners, and dealers will reinstall the chassis skirt with proper clearance, free of charge. If necessary, the fuel tank will be replaced. The recall began on March 31, 2014. Owners may contact Navistar at 1-800-448-7825. Navistar's recall number is 13517.

Reported: 2015-11-20 (November 20, 2015) · Model years: 2013, 2014

Navistar, Inc. is recalling certain model year 2013-2014 International ProStar and DuraStar trucks manufactured April 26, 2012, to April 4, 2013, WorkStar trucks manufactured April 27, 2012, to March 29, 2013, LoneStar trucks manufactured May 21, 2012, to April 2, 2013, and TranStar trucks manufactured April 30, 2012, to March 25, 2013. In the affected vehicles, the accelerator pedal position sensor can move and result in a high engine idle.

Consequence: A high engine idle may make downshifting the transmission difficult and the engine brake may be disabled. These factors may hinder slowing down the truck when descending a long grade, thereby increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will recalibrate the electronic control module (ECM) to allow it to recognize that the pedal is at the idle position, free of charge. The recall began on January 19, 2016. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 15517.

Reported: 2014-03-07 (March 7, 2014) · Model years: 2014

Navistar, Inc. is recalling certain model year 2014 International Prostar trucks manufactured September 2013 through December 2013, and equipped with feature code 14GXP 6X2 rear axles with 'R' hubs and Dual Track rear axles. In the affected vehicles, axle shafts of an incorrect length may have been installed which can cause the splines on the axles shafts to be only partially engaged into the side gears of the rear axle differential.

Consequence: The partial engagement could cause the axle shaft splines or side gears to fail which may result in loss of power to the drive wheels causing the vehicle to stall on the roadway, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace the incorrect wheel hubs and axle shafts with the correct ones and replace any damaged side gears, free of charge. The recall began on March 18, 2014. Owners may contact Navistar at 1-800-448-7825. Navistar's number associated with this recall is 14506.

Reported: 2014-04-17 (April 17, 2014) · Model years: 2014, 2015

Navistar, Inc. (Navistar) is recalling certain model year 2013-2015 International DuraStar vehicles manufactured November 2012 through December 2013, International WorkStar vehicles manufactured December 2012 through January 2014, and 2014-2015 International TranStar and International ProStar vehicles manufactured January 2013 through February 2014. The affected vehicles are built with air disc brake feature codes 04WEY, 04WEZ, or 04WZK. These vehicles may have an incorrect number of bolts mounting the brake caliper to the caliper mounting plate and some of the bolts may be improperly torqued.

Consequence: If the air disk brake caliper has loose or missing bolts, the air disk brake caliper may come loose from the mounting plate causing the vehicle to pull left or right while braking and lengthening the distance needed to stop, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace any missing bolts and check the torque of all of the air disk brake caliper bolts, free of charge. The recall began on May 7, 2014. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 14508.

Reported: 2016-07-26 (July 26, 2016) · Model years: 2014, 2015, 2016, 2017

Navistar, Inc. (Navistar) is recalling certain model year 2014-2017 International ProStar trucks manufactured June 11, 2013, through May 19, 2016. In the affected vehicles, the connection for the cube fuse terminal may break resulting in a total loss of power to the cab and an unexpected engine stall.

Consequence: An unexpected engine stall can increase the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace the cube fuse with a chassis-mounted power distribution module (PDM), free of charge. An interim notice was sent to owners on September 14, 2016. The recall began on October 28, 2016. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 16508.

Reported: 2015-03-23 (March 23, 2015) · Model years: 2015, 2016

Navistar, Inc. (Navistar) is recalling certain model year 2015-2016 International 9900, DuraStar, LoneStar, PayStar, ProStar, WorkStar and 2015 International TranStar and IC Bus CE vehicles equipped with a Haldex air braking system. The affected brake actuators may have been manufactured with an incomplete attachment of the internal rubber diaphragm to the actuation mechanism. This could cause dragging or overheated brakes.

Consequence: If the brakes drag and overheat there is an increased risk of a wheel end fire.

Remedy: Navistar will notify owners, and dealers will replace the Haldex Life Seal Brake chambers, free of charge. The recall began on June 19, 2015. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 15504. Note: This recall supersedes recall 14V-806.

Reported: 2015-10-08 (October 8, 2015) · Model years: 2016

Navistar Inc. (Navistar) is recalling certain model year 2016 International ProStar trucks manufactured August 5, 2015, to August 14, 2015, DuraStar trucks manufactured August 7, 2015, to August 13, 2015, Paystar trucks manufactured August 11, 2015, to August 14, 2015, and LoneStar trucks manufactured August 10, 2015, to August 14, 2015. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.

Consequence: An engine that stalls without warning increases the risk of a crash.

Remedy: Navistar will notify owners, and Cummins dealers will replace the ECM, free of charge. The recall began on October 22, 2015. Owners may contact Navistar customer service at 1-800-448-7825, or Cummins customer service at 1-800-343-7357.

Reported: 2015-10-23 (October 23, 2015) · Model years: 2016

Navistar, Inc. (Navistar) is recalling certain model year 2016 International ProStar trucks manufactured January 5, 2015, to January 7, 2015, and 2016 International TranStar trucks manufactured on January 6, 2015, and equipped with certain Eaton Fuller FR-Series 10-speed manual transmissions. When the transmission shift lever is moved from reverse to neutral, the reverse gear may stay engaged. When the transmission shift lever is moved from reverse to a forward gear position, the transmission may mechanically lock because both the reverse gear and forward gear are simultaneously engaged.

Consequence: Even though the transmission has been shifted out of reverse into neutral, the vehicle may unexpectedly move backwards, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will inspect the transmission. Any affected transmission will be repaired or replaced, free of charge. The recall began on November 20, 2015. Owners may contact Navistar customer service at 1-800-343-7357. Navistar's number for this recall is 15516.

Reported: 2017-03-14 (March 14, 2017) · Model years: 2016, 2017

Navistar Inc. (Navistar) is recalling certain 2016-2018 International LT, 2016-2017 International ProStar, 2017-2018 International LoneStar and International RH heavy diesel trucks. The air dryer mounting bracket may fracture, causing air system leaks or a loss of air pressure to the brake system.

Consequence: A loss of brake air pressure could lengthen the distance needed to stop the vehicle, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will replace the air dryer mounting bracket, free of charge. The recall began on May 12, 2017. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for the recall is 17502.

Reported: 2017-09-20 (September 20, 2017) · Model years: 2016

Navistar, Inc. (Navistar) is recalling certain 2016 International DuraStar, LoneStar, ProStar, TerraStar, TranStar, WorkStar, 9900i, and IC Bus HC vehicles equipped with certain Spicer D or E series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen.

Consequence: If the tie rod loosens, it may disconnect from the steering knuckle, causing a complete loss of steering, increasing the risk of a crash.

Remedy: Navistar will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary, free of charge. The recall began on November 8, 2017. Owners may contact Navistar customer service at 1-331-332-1590. Navistar's number for this recall is 17507.

Reported: 2016-06-21 (June 21, 2016) · Model years: 2017

Navistar, Inc. (Navistar) is recalling certain model year 2017 International ProStar, LoneStar, PayStar, HX, and 9900 trucks equipped with a Cummins ISX15L engine using certain engine control modules (ECM). These ECM's may experience an internal electrical short that can cause a fuse to blow, resulting in an unexpected engine stall without the ability to restart the engine.

Consequence: An engine stall can increase the risk of a crash.

Remedy: Cummins will notify owners, and Cummins dealers will replace the ECM, free of charge. The recall began on July 8, 2016. Owners may contact Cummins customer service at 1-800-343-7357 or Navistar customer service at 1-331-332-1590.

Reported: 2016-12-28 (December 28, 2016) · Model years: 2017

Navistar, Inc. (Navistar) is recalling certain 2017 International ProStar, LoneStar, 9900i, and TranStar trucks. The affected vehicles have a metallic battery cover latch that may unlatch and contact the battery jump start stud, causing an electrical short to ground if the jump start stud is not covered.

Consequence: An electrical short to ground increases the risk of a fire.

Remedy: Navistar will notify owners, and dealers will install a latch stop to prevent the latch from rotating to the unlatched position, free of charge. The recall began on January 27, 2017. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 16513.

Reported: 2018-09-05 (September 5, 2018) · Model years: 2017, 2018

Navistar, Inc. (Navistar) is recalling certain 2017-2018 International ProStar and 9900i trucks, 2018-2019 International LT trucks, 2017-2019 International LoneStar and HX trucks and 2017 International PayStar trucks, equipped with Cummins ISX15 or X15 diesel engines. In certain driving conditions, such as on a long down-hill grade, the fuel line may burst if the fuel pump cooling circuit screen becomes restricted.

Consequence: If the fuel line bursts, fuel may leak onto the road resulting in a roadway hazard for other motorists. The engine may also stall without warning, resulting in the vehicle's inability to restart, increasing the risk of a crash.

Remedy: Cummins will notify the affected owners and dealers will replace the nylon fuel line with a steel fuel line, free of charge. Navistar issued owners an interim notification on October 11, 2018. The recall began November 21, 2018. Owners may contact Navistar customer service at 1-800-448-7825, or Cummins customer service at 1-800-286-6467.

Reported: 2019-02-26 (February 26, 2019) · Model years: 2017, 2018

Navistar, Inc. (Navistar) is recalling certain 2016-2020 International LT and 2017-2018 Prostar 73-inch sleeper cab models equipped with feature code 07BKP or 07BKR (exhaust system with horizontal after treatment device and horizontal tailpipe mounted on right side). In the affected vehicles, the rear exhaust hanger bracket may crack, which can cause the forward hanger bracket to also crack. If both brackets crack, the exhaust tail pipe may detach from the vehicle.

Consequence: If the exhaust tail pipe detaches from the vehicle while being driven, it can become a road hazard, increasing the risk of crash.

Remedy: Navistar will notify owners, and dealers will replace the rear exhaust hanger bracket and replace any forward bracket found cracked and any exhaust tailpipe found damaged, free of charge. The recall began April 23, 2019. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 19501.

Reported: 2023-04-06 (April 6, 2023) · Model years: 2017, 2018, 2019

Navistar, Inc. (Navistar) is recalling certain 2016-2017 International TranStar, 2017-2019 International ProStar, International LoneStar, 2017-2020 International DuraStar, WorkStar, and 2018-2019 IC Bus HC Commercial buses. The heating, ventilation, and air-conditioning (HVAC) blower motor circuit may have an insufficient wiring terminal that can overheat.

Consequence: An overheated electrical circuit can increase the risk of a fire.

Remedy: Dealers will replace the HVAC blower motor load circuit wiring terminal, free of charge. Owner notification letters are expected to be mailed June 5, 2023. Owners may contact Navistar's customer service at 1-800-448-7825. Navistar's number for this recall is 23510.

Reported: 2018-05-03 (May 3, 2018) · Model years: 2018, 2019

Navistar, Inc. (Navistar) is recalling certain 2018-2019 International WorkStar, DuraStar, LoneStar, LT, ProStar, RH and IC Bus HC, 2018 International TranStar, 2019 International HV and MV trucks and transit buses. The front driver and passenger seat belt anchor D-ring bolt may break in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages."

Consequence: If the D-ring bolt breaks during a crash, the seat occupant may not be properly restrained, increasing their risk of injury.

Remedy: Navistar has notified owners, and dealers will replace the D-ring bolt depending on the information found on the seat belt label, free of charge. The recall began May 23, 2018. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 18505.

Reported: 2018-11-21 (November 21, 2018) · Model years: 2018, 2019

Navistar, Inc. (Navistar) is recalling certain 2019 International HV, MV, 2018-2019 HX, LT, RH, LoneStar, ProStar, WorkStar, and 2018 TranStar automated manual transmission vehicles, equipped with certain Eaton ECA heavy-duty truck clutches. An internal component in the clutch assembly may fail, possibly resulting in unintended vehicle movement.

Consequence: Unintended vehicle movement can increase the risk of a crash.

Remedy: Navistar will notify owners, and dealers will recalibrate the Transmission Control Module (TCM), free of charge. The recall began January 18, 2019. Owners may contact Navistar customer service at 1-800-448-7825. Navistar's number for this recall is 18518.

Reported: 2024-10-31 (October 31, 2024) · Model years: 2022

International Motors, LLC (International) is recalling certain 2021-2024 Lonestar, 2021-2025 RH, HV, MV, LT, HX, and 2022 PROSTAR vehicles, equipped with Bendix EC80 Advanced Electronic Control Units (ECU). Electrical noise and low signal to the power line carrier may cause the ECU to incorrectly process commands or stop working.

Consequence: Safety systems that depend on the ECU (Automatic Traction Control, ABS, Electronic Stability Control, Active Cruise Control, and Collison Mitigation System) may have diminished or lost functionality, increasing the risk of a crash.

Remedy: International will work with Bendix to reprogram the ECU software, free of charge. Owner notification letters were mailed December 16, 2024. Owners may contact International customer service at 1-800-448-7825. International's number for this recall is 24515.