Hino NV8J recalls by model year

Reported: 2004-02-25 (February 25, 2004) · Model years: 2005

CERTAIN TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." A REVERSE BACKUP SWITCH MAY HAVE BEEN CONTAMINATED DURING THE MANUFACTURING PROCESS. THE NEUTRAL SAFETY SWITCH MAY NOT ALLOW THE CRUISE CONTROL TO ENGAGE.

Consequence: THIS DOES NOT MEET THE REQUIREMENTS OF THE STANDARD. ALSO, THIS COULD CAUSE THE CRUISE CONTROL NOT TO BE ACTIVATED. THE REVERSE BACKUP LIGHT AND BUZZER STAYS ON.

Remedy: DEALERS WILL REPLACE THE SWITCHES. OWNER NOTIFICATION BEGAN ON APRIL 19, 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HINO AT 1-845-365-1400.

Reported: 2004-04-28 (April 28, 2004) · Model years: 2005

ON CERTAIN TRUCKS, THE PINCH BOLT NUT OF THE YOKE CONNECTING THE STEERING GEARBOX AND THE STEERING WHEEL SHAFT BACKED OUT.

Consequence: THIS COULD CAUSE THE YOKE AND THE STEERING WHEEL SHAFT TO SEPARATE WHICH COULD RESULT IN LOSS OF STEERING INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT AND RETORQUE THE PINCH BOLT NUT AS NECESSARY. OWNER NOTIFICATION BEGAN MAY 7, 2004. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HINO AT 1-845-365-1400.

Reported: 2004-09-13 (September 13, 2004) · Model years: 2005

ON CERTAIN CAB AND CHASSIS TRUCKS, WHEN EXCESSIVE FORCE IS APPLIED TO THE ACCELERATOR PEDAL, BEYOND THAT REQUIRED TO ACHIEVE FULL ACCELERATION, THE PEDAL MAY BECOME WEDGED BETWEEN THE FLOOR PANEL AND THE CARPET.

Consequence: WHEN THIS OCCURS, THE ACCELERATOR PEDAL WILL BECOME WEDGED IN THE FULL THROTTLE POSITION WHICH COULD RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL INSPECT THE ACCELERATOR PEDAL HEIGHT TO DETERMINE IF IT IS WITHIN SPECIFICATIONS. IF EITHER THE PEDAL HEIGHT OR THE ACCELERATOR ROD IS NOT WITHIN SPECIFICATIONS, REPLACE THE ACCELERATOR ASSEMBLY. IN ADDITION, A NEW BRACKET CONTAINING AN ACCELERATOR PEDAL STOPPER WILL BE INSTALLED. THE RECALL BEGAN ON SEPTEMBER 8, 2004. OWNERS SHOULD CONTACT HINO CUSTOMER SERVICE AT 1-845-365-1400.

Reported: 2004-09-20 (September 20, 2004) · Model years: 2005

ON CERTAIN TRUCKS, WHEN THE STEERING WHEEL IS BEING TURNED, THE DUST COVER MAY TWINE WITH THE STEERING SHAFT AND COULD RESULT IN THE STEERING WHEEL OPERATION BECOMING HEAVY.

Consequence: LOSS OF STEERING CONTROL MAY OCCUR, WHICH COULD RESULT IN A CRASH.

Remedy: DEALERS WILL REMOVE THE OLD DUST COVER AND INSTALL A NEWLY DESIGNED COVER. THE RECALL BEGAN OCTOBER 8, 2004. OWNERS SHOULD CONTACT HINO AT 1-845-365-1400.

Reported: 2005-05-25 (May 25, 2005) · Model years: 2005, 2006

ON CERTAIN TRUCK CAB AND CHASSIS VEHICLES, A BRAKE AIR LINE COULD BECOME DISCONNECTED.

Consequence: THIS COULD CAUSE A DECREASE OF BRAKING ABILITY OR THE PARKING BRAKE TO APPLY WITHOUT BEING ACTIVATED, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT EACH VEHICLE AND CHECK THE TORQUE ON THE NUTS. IF THE NUTS ARE NOT TORQUED PROPERLY, THEY WILL BE TIGHTENED TO THE PROPER SPECIFICATION. THE RECALL BEGAN ON JUNE 4, 2005. OWNERS MAY CONTACT HINO AT 1-248-648-6400.

Reported: 2006-05-10 (May 10, 2006) · Model years: 2005, 2006

ON CERTAIN TRUCKS EQUIPPED WITH BANDO BELT TENSIONER, CORROSION OR RUST MAY DEVELOP ON THE TENSIONER SPINDLE OR BUSHING CAUSING THE AUTO TENSIONER TO BECOME STIFF OR BIND. THIS CAN CAUSE THE DRIVE BELT TO SUDDENLY COME OFF OR THE AUTO TENSIONER MOUNTING BOLTS COULD SUDDENLY BREAK.

Consequence: IF THE DRIVE BELT COMES OFF, THE ALTERNATOR WARNING LAMP WILL ILLUMINATE. IF THE WARNING IS IGNORED, THIS CONDITION COULD ULTIMATELY RESULT IN A LOSS OF VEHICLE POWER (ENGINE STALL) INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE AUTO TENSIONER, INSTALL UPGRADED MOUNTING BOLTS, AND REPLACE THE ACCESSORY DRIVE BELT FREE OF CHARGE. THE RECALL BEGAN ON MAY 2, 2006. OWNERS MAY CONTACT HINO MOTORS AT 248-648-6430. THIS CAMPAIGN HAS BEEN SUPERSEDED - PLEASE SEE 07V208.

Reported: 2006-05-18 (May 18, 2006) · Model years: 2005, 2006, 2007

ON CERTAIN TRUCKS, DURING ASSEMBLY, THE DRAG LINK ATTACHMENT NUTS AT THE PITMAN ARM AND STEERING ARM MAY HAVE BEEN INCORRECTLY TORQUED. RESIDUAL GREASE AND PAINT WHICH WAS APPLIED AS A RUST INHIBITOR ON THE STEERING ARM MAY HAVE CONTRIBUTED TO A LOSS OF TORQUE AFTER ASSEMBLY.

Consequence: INCREASED WEAR FOR THE DRAGLINK CONNECTIONS CAN OCCUR CREATING A NOTICEABLE INCREASE IN THE AMOUNT OF STEERING WHEEL FREE PLAY. IF THIS CONDITION WAS IGNORED, A LOSS OF STEERING CONTROL OF THE VEHICLE COULD OCCUR WHICH COULD RESULT IN A CRASH.

Remedy: DEALERS WILL INSPECT THE STEERING ARM TIGHTNESS AND REMOVE ALL GREASE AND PAINT FROM THE STEERING ARMS AND RETORQUE THE DRAGLINK ATTACHMENT NUTS AT THE STEERING ARM AND PITMAN ARM. THE RECALL BEGAN ON MAY 12, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6430.

Reported: 2007-05-09 (May 9, 2007) · Model years: 2005, 2006, 2007

ON CERTAIN TRUCKS EQUIPPED WITH BANDO BELT TENSIONER, CORROSION OR RUST MAY DEVELOP ON THE TENSIONER SPINDLE OR BUSHING CAUSING THE AUTO TENSIONER TO BECOME STIFF OR BIND. THIS CAN CAUSE THE DRIVE BELT TO SUDDENLY COME OFF OR THE AUTO TENSIONER MOUNTING BOLTS COULD SUDDENLY BREAK.

Consequence: IF THE DRIVE BELT COMES OFF, THE ALTERNATOR WARNING LAMP WILL ILLUMINATE. IF THE WARNING IS IGNORED, THIS CONDITION COULD ULTIMATELY RESULT IN A LOSS OF VEHICLE POWER (ENGINE STALL) INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE AUTO TENSIONER, INSTALL UPGRADED MOUNTING BOLTS, AND REPLACE THE ACCESSORY DRIVE BELT FREE OF CHARGE. THE RECALL BEGAN ON APRIL 25, 2007. OWNERS MAY CONTACT HINO MOTORS AT 248-648-6430. NOTE: THIS RECALL SUPERSEDES A PREVIOUS CAMPAIGN (PLEASE SEE 06V157).

Reported: 2008-04-30 (April 30, 2008) · Model years: 2005, 2006, 2007, 2008

HINO IS RECALLING 16,805 MY 2005-2008 NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, AND NV8J TRUCKS. THE TWO VERTICAL RIGHT/LEFT SIDE FRONT SPRING BRACKET BOLTS WERE NOT TIGHTENED PROPERLY DURING THE ASSEMBLY PROCESS. THIS MAY CAUSE INCREASED STRESS ON THE SPRING BRACKET WHICH CAN LEAD TO CRACKING OF THE BRACKET.

Consequence: THIS COULD REDUCE STEERING CONTROL INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE VERTICAL FRONT SPRING BRACKET ATTACHMENT BOLTS ON RIGHT/LEFT HANGER BRACKETS AND RE-TORQUE ALL ASSOCIATED BOLTS FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 8, 2008. OWNERS MAY CONTACT HINO AT 248-699-9300.

Reported: 2012-12-03 (December 3, 2012) · Model years: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013

Hino is recalling certain model year 2005 through 2013 medium duty trucks, models NA6J, NB6J, NC6J, ND8J, NE8J, NJ8J, NF8J, and NV8J, manufactured from August 18, 2003, through November 16, 2011. Over time, the main B+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the B+ circuit and its convoluted tubing sheath.

Consequence: If the B+ circuit shorts to ground, it may lead to a fire.

Remedy: Hino will notify owners, and dealers will repair the vehicles free of charge. The recall began on January 17, 2013. Owners may contact Hino at 1-248-699-9390.

Reported: 2005-10-24 (October 24, 2005) · Model years: 2006

ON CERTAIN TRUCKS, THE BOLTS THAT HOLD THE BATTERY BOX AND BRACKET IN PLACE MAY NOT HAVE BEEN PROPERLY TORQUED AT THE TIME OF ASSEMBLY.

Consequence: THE BATTERY BOX COULD BECOME LOOSE AND POSSIBLY FALL RESULTING IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL INSPECT AND RETORQUED ALL BOLTS. THE RECALL BEGAN ON OCTOBER 27, 2005. OWNERS MAY CONTACT HINO AT 248-648-6430.

Reported: 2006-09-19 (September 19, 2006) · Model years: 2006, 2007

ON CERTAIN CAB AND CHASSIS TRUCKS THAT WERE TRANSPORTED TO THE SELLING LOCATION OR BODY COMPANY USING A DECKING SYSTEM (VEHICLES STACKED ON THE REAR OF THE LEAD TRUCK FOR TRANSPORT), THE AIR BRAKE LINES MAY BE DISCONNECTED SO THAT THE BRAKING SYSTEMS CAN BE TIED TOGETHER WITH THE OTHER VEHICLES. WHEN THESE VEHICLES ARRIVE AT THEIR DESTINATION, THE AIR BRAKE LINES ARE RECONNECTED. THESE RECONNECTIONS WERE NOT ALWAYS BEING TIGHTENED TO THE PROPER TORQUE. ALSO, DURING THIS RECONNECTION PROCESS, SOME OF THE ABS WIRING CLIPS HAD BEEN REMOVED AND NOT REINSTALLED.

Consequence: LOOSE AIR BRAKE LINES CAN BECOME DISCONNECTED OR LEAK WHICH COULD CAUSE A DECREASE IN BRAKING ABILITY OR RESULTING IN APPLICATION OF THE PARKING BRAKE WITHOUT IT BEING ACTIVATED. THIS COULD RESULT IN A CRASH. ALSO IF THE DRIVE SHAFT BOLTS ARE LEFT LOOSE, THE DRIVE SHAFT COULD BECOME DISENGAGED MAKING THE VEHICLE IMMOVABLE. IF THE ABS SENSORS ARE NOT SECURED PROPERLY USING THE CORRECT CLIPS, THE ABS SENSORS COULD GO OUT OF ALIGNMENT.

Remedy: DEALERS WILL INSPECT THE AIR BRAKE LINES, DRIVE SHAFT BOLTS AND ABS SENSOR CLIPS AND TIGHTEN AND REPAIR IF NECESSARY. THE RECALL BEGAN ON SEPTEMBER 15, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6430.

Reported: 2006-12-15 (December 15, 2006) · Model years: 2006, 2007

ON CERTAIN VEHICLES, DURING THE STAMPING PROCESS, SOME CROSSMEMBERS WERE MANUFACTURED WITH A DEFORMATION TO THE LOWER CORNERS DUE TO EXCESSIVE WEAR OF THE STAMPING DIE. OVER TIME, IF THIS CONDITION WERE IGNORED, THE STRUCTURAL INTEGRITY OF THE CROSSMEMBERS COULD BE COMPROMISED WHICH COULD RESULT IN A LOSS OF BRAKING ABILITY, SEPARATION OF THE PROPELLER SHAFT AND/OR A LOSS OF REAR WARNING LAMPS.

Consequence: ANY OF THESE OCCURRENCES COULD RESULT IN A CRASH.

Remedy: DEALERS WILL INSPECT, CORRECT, AND REPLACE THE CROSSMEMBERS. THE RECALL BEGAN ON DECEMBER 4, 2006. OWNERS MAY CONTACT HINO AT 1-248-648-6400.

Reported: 2008-09-18 (September 18, 2008) · Model years: 2007, 2008, 2009

HINO IS RECALLING 1,195 MY 2007-2009 NV8J TRUCKS. DURING THE MANUFACTURING PROCESS, THE PROPELLER SHAFT BOLTS MAY NOT HAVE BEEN PROPERLY TIGHTENED DURING THE MANUFACTURING PROCESS.

Consequence: IF THE BOLTS WERE TO LOOSEN, IT COULD CAUSE A VIBRATION IN THE DRIVELINE. IF THIS VIBRATION WERE IGNORED, THE PROPELLER SHAFT COULD SEPARATE FROM THE MATING FLANGE. THIS COULD POTENTIALLY RESULT IN DAMAGE TO PROPERTY AND/OR RESULT IN A CRASH.

Remedy: DEALERS WILL REPLACE THE PROPELLER SHAFT BOLTS. THE RECALL BEGAN ON OCTOBER 14, 2008. OWNERS MAY CONTACT HINO AT 1-248-699-9300.

Reported: 2007-10-30 (October 30, 2007) · Model years: 2008

ON CERTAIN TRUCKS, THE SIDE VIEW MIRRORS MAY HAVE BEEN INSTALLED INCORRECTLY POSSIBLY LEADING TO THE MIRROR GLASS DETACHING FROM THE MIRROR HOUSING.

Consequence: IF THE MIRROR GLASS IS LOST, THE DRIVER MAY NOT BE ABLE TO SEE TRAFFIC APPROACHING FROM THE REAR INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE SIDE VIEW MIRRORS AND, IF NECESSARY, REPLACE THE MIRROR MATERIALS. THE RECALL BEGAN ON JUNE 12, 2007. OWNERS MAY CONTACT HINO AT 1-248-648-6490.

Reported: 2008-11-24 (November 24, 2008) · Model years: 2008

HINO IS RECALLING 3,836 MY 2008 ND8J, NE8J, NJ8J, AND NV8J CLASS 6 AND 7, CONVENTIONAL CAB, MEDIUM DUTY TRUCKS EQUIPED WITH J08E-TV OR J08E-TW ENGINES. THERE IS AN IMPROPER SHAPE OF THE SUPPLY PUMP COUPLER LOCATED BETWEEN THE SUPPLY PUMP AND THE AIR COMPRESSOR. THE COUPLING MAY CRACK, THE GEAR TRAIN AND VALVES OF THE ENGINE COULD BREAK, AND THE ENGINE COULD STOP RUNNING.

Consequence: THIS WOULD DISABLE THE POWER STEERING SYSTEM, STOP THE SUPPLY OF AIR TO THE AIR TANK, AND MAY RESULT IN INSUFFICIENT BRAKING POWER, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPAIR THE COUPLING. THE RECALL BEGAN ON JANUARY 5, 2009. OWNERS MAY CONTACT HINO AT 1-248-699-9330.

Reported: 2010-04-15 (April 15, 2010) · Model years: 2008, 2009, 2010

HINO IS RECALLING CERTAIN MODEL YEAR 2008-2010 NV8J TRUCKS EQUIPPED WITH ALLISON 3000 RDS AUTOMATIC TRANSMISSION. THE DRIVE COUPLER BOLTS MAY NOT HAVE BEEN PROPERLY TIGHTENED AT THE FACTORY DUE TO THE INCORRECT TOOL POSSIBLY BEING USED DURING THE MANUFACTURING PROCESS.

Consequence: IF THE DRIVE COUPLER BOLTS WERE TO LOOSEN IT COULD CAUSE A VIBRATION IN THE DRIVELINE. IF THIS VIBRATION WERE IGNORED, THE DRIVE COUPLER BOLTS COULD SHEAR AND THE COUPLING BETWEEN THE ENGINE AND TORQUE CONVERTER WOULD NOT TRANSMIT POWER. THIS ULTIMATELY COULD RESULT IN A CRASH.

Remedy: HINO WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2010. OWNERS MAY CONTACT HINO AT 1-248-699-9330.

Reported: 2008-12-18 (December 18, 2008) · Model years: 2009

HINO IS RECALLING 130 MY 2008-2009 ND8J, NE8J, NJ8J, AND NV8J CONVENTIONAL TRUCKS. THE REAR AXLE U-BOLTS WERE NOT PROPERLY TIGHTENED. THE LOWER SPRING SEAT MAY NOT CONTACT THE AXLE HOUSING PROPERLY, PRODUCING A GAP ON THE FRONT OR REAR SIDE OF THE AXLE HOUSING.

Consequence: THIS GAP COULD ALLOW THE U-BOLTS TO LOOSEN AND/OR CAUSE THE LOWER SPRING SEAT TO CRACK. THE AXLE COULD BECOME MISALIGNED AND/OR SEPARATED FROM THE MOUNTINGS INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE REAR AIR SUSPENSION LOWER SPRING SEAT FOR A GAP BETWEEN THE REAR AXLE AND LOWER SPRING SEAT. THE U-BOLTS WILL BE TIGHTENED TO THE SPECIFIED TORQUE. THE RECALL BEGAN ON JANUARY 19, 2009. OWNERS MAY CONTACT HINO AT 1-248-699-9330.

Reported: 2010-04-16 (April 16, 2010) · Model years: 2009, 2010

HINO IS RECALLING CERTAIN TRUCKS WITH VERTICAL EXHAUST PIPES. CERTAIN BOLTS ATTACHING THE EXHAUST SYSTEM TO THE TRUCK MAY NOT HAVE BEEN PROPERLY TIGHTENED DURING THE MANUFACTURING PROCESS. THE BOLTS COULD FAIL ALLOWING THE EXHAUST SYSTEM TO SEPARATE FROM THE TRUCK.

Consequence: THE EXHAUST SYSTEM COULD FALL ONTO THE ROADWAY AND BE STRUCK BY A FOLLOWING VEHICLE RESULTING IN A CRASH.

Remedy: HINO WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2010. OWNERS MAY CONTACT HINO AT 248-699-9330.

Reported: 2010-04-16 (April 16, 2010) · Model years: 2009, 2010

HINO IS RECALLING CERTAIN MODEL YEAR 2009-2010 NV8J TRUCKS. THE U-JOINT ATTACHMENT BOLTS MAY NOT HAVE BEEN PROPERLY TIGHTENED DURING THE MANUFACTURING PROCESS.

Consequence: IF THE BOLTS WERE TO LOOSEN IT COULD CAUSE A VIBRATION IN THE DRIVELINE. IF THIS VIBRATION WERE IGNORED, THE U-JOINT ATTACHMENT BOLTS COULD SHEAR AND A PORTION OF THE PROPELLER SHAFT COULD SEPARATE FROM THE VEHICLE, THUS FALLING ONTO THE SURFACE OF THE ROADWAY AND BE STRUCK BY A VEHICLE RESULTING IN A CRASH.

Remedy: HINO WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 9, 2010. OWNERS MAY CONTACT HINO AT 248-699-9330.

Reported: 2011-01-19 (January 19, 2011) · Model years: 2011

HINO IS RECALLING CERTAIN MODEL YEAR 2011 NJ8J AND NV8J HEAVY TRUCKS MANUFACTURED FROM OCTOBER 26, 2009, THROUGH OCTOBER 1, 2010. TWO OF THE AIRLINES TO THE FRONT AND REAR AIR TANKS MAY HAVE BEEN INSTALLED INCORRECTLY.

Consequence: IN THE EVENT THAT THE REAR TANK AIR PRESSURE WAS DEPLETED, BRAKING FUNCTION WOULD BE LOST AND THE AUTOMATIC ENGAGEMENT OF THE SPRING BRAKES WILL NOT OCCUR, POSSIBLY RESULTING IN A CRASH.

Remedy: HINO WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 1, 2011. OWNERS MAY CONTACT HINO AT 1-248-699-9300.

Reported: 2017-09-28 (September 28, 2017) · Model years: 2011, 2012

Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain 2011-2012 NE8J, NJ8J, and NV8J trucks. The engines have a wrist pin bushings in the connecting rods that may shift and cause excessive cylinder wear.

Consequence: Excessive wear of the cylinders can result in engine failure, increasing the risk of a crash.

Remedy: Hino will notify owners, and dealers will inspect and, as necessary, replace the connecting rods. Interim notices informing owners of the safety risk were mailed November 27, 2017. The recall began on March 19, 2018. Owners may contact Hino customer service at 1-248-699-9300. Hino's number for this recall is AA860.

Reported: 2011-11-03 (November 3, 2011) · Model years: 2012

HINO IS RECALLING CERTAIN MODEL 2012 ND8J, NE8J, NJ8J, AND NV8J COMMERCIAL TRUCKS MANUFACTURED FROM JULY 25, 2011, THROUGH SEPTEMBER 16, 2011. DURING ASSEMBLY, THE WHEEL-END RETAINER ON THE FRONT OR REAR AXLE MAY HAVE BEEN INSTALLED INCORRECTLY.

Consequence: THE WHEEL-HUB AND AXLE SHAFT CAN SEPARATE FROM THE VEHICLE, POSSIBLY RESULTING IN A CRASH.

Remedy: HINO WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE FRONT AXLE ASSEMBLIES AND, IF THE AXLE IS FOUND TO BE INCORRECTLY ASSEMBLED, DEALERS WILL REPLACE THE WHEEL END RETAINING HARDWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 19, 2012. OWNERS MAY CONTACT HINO AT 1-248-699-9390.

Reported: 2013-12-16 (December 16, 2013) · Model years: 2013

Hino Motor Sales (Hino) is recalling certain model year 2013 NV8J vehicles manufactured November 13, 2012, through February 8, 2013. The affected vehicles were modified to have a lower Gross Vehicle Weight Rating (GVWR), however the vehicle documentation shows the full GVWR. As such, the information on the documents does not conform to Federal Motor Vehicle Safety Standard (FMVSS) Part 567 "Certification."

Consequence: An operator relying on the documents to determine the truck's GVWR may load the vehicle beyond the actual weight rating, possibly resulting in tire or suspension failure, increasing the risk of a crash.

Remedy: Hino will notify owners, and dealers will inspect and replace the documents, as necessary, free of charge. All of the owners have been notified as of January 29, 2014. Customers may contact Hino at 1-248-699-9330. Hino's number for this recall is M0270.

Reported: 2017-08-07 (August 7, 2017) · Model years: 2018

Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain 2018 NE8J, NJ8J, and NV8J vehicles. The door hinge bolts on these vehicles may not be sufficiently tightened, possibly allowing the door to open while driving. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."

Consequence: The loose door hinges can cause the door to operate improperly and possibly open, increasing the risk of a crash or injury.

Remedy: Hino will notify owners, and dealers will tighten the door hinge bolts, as necessary, free of charge. The recall began on October 9, 2017. Owners may contact Hino customer service at 1-248-699-9300. Hino's number for this recall is M0300.

Reported: 2018-02-19 (February 19, 2018) · Model years: 2018, 2019

Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain 2018-2019 NE8J, NJ8J and NV8J trucks. The terminal bolts that secure the main fuse terminals within the fuse block may not have been properly tightened, possibly resulting in electrical arcing and overheating, or an engine shutdown.

Consequence: An electrical arc or overheating can increase the risk of a fire. An engine shutdown can increase the risk of a crash.

Remedy: Hino will notify owners, and dealers will tighten any loose terminal bolts and replace any damaged electrical harness, free of charge. The recall began on March 10, 2018. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is M0320.

Reported: 2018-03-15 (March 15, 2018) · Model years: 2018, 2019

Hino Motor Sales U.S.A., Inc. (Hino) is recalling certain 2018-2019 NE8J, NJ8J, and NV8J trucks. The engine valve train adjustment screw lock nuts may not have been properly tightened manufacturing, possibly resulting in them coming loose within the engine and damaging it.

Consequence: The damage to the engine may result in it shutting off and increasing the risk of a crash.

Remedy: Hino will notify owners, and dealers will inspect the torque on the valve train adjustment screw lock nuts. If a nut is found missing, the engine will be replaced, free of charge. The recall began on May 18, 2018. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AA9Q0.

Reported: 2019-07-31 (July 31, 2019) · Model years: 2020

Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2020 NE8J, NJ8J, and NV8J vehicles. Due to improper adhesive bonding, the exterior mirror glass may detach from the mirror carrier plate.

Consequence: If the mirror glass detaches, the driver may have reduced visibility, increasing the risk of a crash.

Remedy: Hino will notify owners, and dealers will replace the mirrors, free of charge. The recall began October 1, 2019. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is M0330.

Reported: 2020-04-30 (April 30, 2020) · Model years: 2020, 2021

Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2020-2021 NV8J, NJ8J, NE8J, NJ8A, NV8A, NE8A, NE8G, NJ8C, NE8C, and NV8G trucks. The ground cable that connects the negative battery terminal to the frame may be too short and may break as a result.

Consequence: If the ground cable breaks, the engine cannot be re-started to move the vehicle to a safe area, increasing the risk of a crash.

Remedy: Hino will notify owners, and dealers will install an extension bracket to the negative battery terminal and inspect the ground cable terminal for damage, replacing the cable if damage is found, free of charge. Owners will be notified of the safety risk with an interim letter Mid-June 2020. The recall began June 26, 2020. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is AAHT0.

Reported: 2021-03-08 (March 8, 2021) · Model years: 2020

Hino Motors Sales U.S.A., Inc. (Hino) is recalling certain 2020 NE8J, NJ8J, NV8J, NH1A, NV1A and TH1A vehicles. The mirror glass may not be bonded properly to the carrier plate, allowing it to detach.

Consequence: Detached mirror glass can reduce driver visibility, or become a road hazard to other drivers. Either of these scenarios can increase the risk of a crash.

Remedy: Hino will notify owners, and dealers will inspect the mirror production date, and replace it if necessary, free of charge. Owner notification letters were mailed on May 7, 2021. Owners may contact Hino customer service at 1-248-699-9390. Hino's number for this recall is M0340. This recall supersedes previous NHTSA recall number 19V-564.