Chrysler NEW YORKER recalls by model year

Reported: 1977-11-16 (November 16, 1977) · Model years: 1972, 1973

AN INTERRUPTION OF THE MAIN ELECTRICAL POWER FEED CIRCUIT FROM THE BATTERY AND ALTERNATOR MAY OCCUR DUE TO SEPARATION OF A TERMINAL CONNECTION IN THE WIRING CIRCUIT. THE TERMINAL END OF THE POWER FEED WIRE COMING FROM THE COMPARTMENT MAY SEPARATE FROM ITS MATING TERMINAL ON THE WIRE GOING INTO THE PASSENGER COMPARTMENT AT THE MULTIPLE CIRCUIT CONNECTOR (KNOWN AS THE BULKHEAD CONNECTOR) LOCATED ON THE LEFT (DRIVER"S) SIDE OF THE ENGINE COMPARTMENT FIREWALL.

Remedy: DEALER WILL REPAIR THE ENGINE COMPARTMENT POWER FEED CIRCUIT WIRE BY INSTALLING AN OVERLAY WIRE ROUTED AROUND THE BULKHEAD CONNECTOR.

Reported: 1974-04-11 (April 11, 1974) · Model years: 1974

Reported: 1975-05-13 (May 13, 1975) · Model years: 1974, 1975

Reported: 1975-02-05 (February 5, 1975) · Model years: 1975

Reported: 1979-01-05 (January 5, 1979) · Model years: 1979

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITH AN OVERSIZED RIGHT FRONT WHEEL BEARING CUP WHICH ALSO PREVENTS THE PLANT LUBRICATING EQUIPMENT FROM CYCLING TO LUBRICATE BOTH THE INNER AND OUTER WHEEL BEARINGS. THE RESULTANT BEARING LOOSENESS AND/OR THE LACK OF LUBRICATION MAY CAUSE BEARING FAILURE AND, POSSIBLY, WHEEL SPINDLE DAMAGE.

Remedy: DEALERS WILL REPLACE THE INNER AND OUTER RIGHT FRONT WHEEL BEARINGS AND BEARING CUPS ON ALL INVOLVED VEHICLES AT NO COST TO OWNERS.

Reported: 1981-05-05 (May 5, 1981) · Model years: 1981

ENGINE MAY LOSE POWER OR STALL DUE TO CARBURETOR FLOODING. THIS IS CAUSED BY A POOR ELECTRICAL GROUND ON THE CARBURETOR FUEL BOWL VENT SOLENOID. VEHICLES MAY ALSO HAVE DRIVEABILITY PROBLEMS WHILE THE ENGINE IS WARMING UP IN COLD WEATHER. THESE PROBLEMS INCLUDE ENGINE MISSING, SAGS, AND HESITATION. THIS IS CAUSED BY A STICKING CARBURETOR OXYGEN FEEDBACK SOLENOID.

Remedy: DEALER WILL INSPECT CARBURETOR AND IF NECESSARY, THE BOWL VENT SOLENOID WILL BE REPAIRED BY RESOLDERING (RECONNECTING) THE EXTERNAL ELECTRICAL CONNECTION FREE OF CHARGE. IF APPLICABLE, THE OXYGEN FEEDBACK SENSOR WILL BE REPLACED.

Reported: 1981-09-22 (September 22, 1981) · Model years: 1981, 1982

THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE "RESUME" POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.

Remedy: THE SHIELD PORTION OF THE "RESUME" SLIDE LEVER IN THE SPEED CONTROL UNIT WILL BE REPLACED WITHOUT CHARGE.

Reported: 1983-06-06 (June 6, 1983) · Model years: 1983

LOCATION OF HYDRAULIC BRAKE TUBE TO BOTH REAR WHEELS CAUSES INTERFERENCE AND CHAFING BETWEEN THE TUBES AND REAR SUSPENSION TRAILING ARM PIVOT BRACKETS.

Remedy: DEALER WILL INSPECT REAR WHEEL BRAKE TUBES AND REROUTE TO ENSURE PROPER TUBE TO PIVOT BRACKET CLEARANCE. ANY DAMAGED TUBES WILL ALSO BE REPLACED.

Reported: 1989-03-29 (March 29, 1989) · Model years: 1983

FRONT SUSPENSION CROSSMEMBER MAY CORRODE AND FAIL AT LOWER CONTROL ARM REAR PIVOT MOUNTS IF OPERATED WHERE SALT IS USED TO AID IN SNOW REMOVAL.

Consequence: CONTROL ARM COULD DETACH FROM THE CROSSMEMBER, ADVERSELYAFFECTING DIRECTIONAL STABILITY, WHICH COULD RESULT IN AN ACCIDENT.

Remedy: INSTALL ATTACHMENT REINFORCEMENT BRACKETS TO PREVENT CONTROL ARM DETACHMENT AS A RESULT OF CORROSION WEAKENING.

Reported: 1985-01-01 (January 1, 1985) · Model years: 1985

AN ENGINE COMPARTMENT FUEL HOSE ROUTED TO THE FUEL SYSTEM PRESSURE REGULATOR MAY HAVE AN INADEQUATELY TIGHTENED HOSE CLAMP. CONSEQUENCE OF DEFECT: THE FUEL HOSE COULD LEAK AND RESULT IN AN ENGINE COMPARTMENT FIRE.

Remedy: REPOSITION AND TIGHTEN TO THE PROPER TORQUE LEVEL OF THE FUEL HOSE CLAMP.

Reported: 1988-07-01 (July 1, 1988) · Model years: 1985, 1986, 1987

FUEL LEAKAGE MAY OCCUR IN LOW AMBIENT TEMPERATURE OPERATION AT CONNECTIONS OF AN ENGINE COMPARTMENT FUEL SUPPLY HOSE TO THE PRESSURE REGULATOR AND TO THE FUEL RAIL.

Consequence: IN THE PRESENCE OF AN IGNITION SOURCE, FUEL LEAKAGE COULDRESULT IN A FIRE.

Remedy: RELOCATE PRESSURE REGULATOR; REPLACE FUEL SUPPLY WITH FORMED HOSE WITH REVISED ROUTING CONFIGURATION TO ENSURE SEALING INTEGRITY.

Reported: 1986-02-19 (February 19, 1986) · Model years: 1986

A RESISTOR IN THE ELECTRONIC PANEL CLUSTER MAY BE SUBJECTED TO AN ELECTRICAL CURRENT OVERLOAD DUE TO FAILURE OF A SWITCHING TRANSISTOR. CONSEQUENCE OF DEFECT: THE OVERHEATED RESISTOR COULD IGNITE AND START AN INSTRUMENT PANEL FIRE.

Remedy: MODIFY INSTRUMENT PANEL CLUSTER BY REPLACING THE RESISTOR WITH A FUSED RESISTOR THAT WILL NOT IGNITE IF OVERLOADED.

Reported: 1986-04-10 (April 10, 1986) · Model years: 1986

BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.

Remedy: REWORK BATTERIES BY PROBING BOTH VENT ORIFICES TO ELIMINATE ANY VENT OBSTRUCTION.

Reported: 1988-04-08 (April 8, 1988) · Model years: 1986

A SERVICE REPLACEMENT DRIVERS SEAT CUSHION (MANUAL SEAT TYPE) MAY CONTAIN WRONG CUSHION WITH A BRACE THAT COULD INTERFERE WITH POWER SEAT ADJUSTER MECHANISM AND CAUSE STRESS ON THE FRAME.

Consequence: SEAT FRAME COULD FRACTURE AND RESULT IN SIGNIFICANTREARWARD MOVEMENT OF THE SEAT BACK.

Remedy: REPLACE FRAME WITH PROPER POWER SEAT FRAME.

Reported: 1991-10-02 (October 2, 1991) · Model years: 1990, 1991

WATER LEAKING UNDER WINDSHIELD COWL IN AREA ABOVE HEATER BLOWER MOTOR RESISTOR BLOCK RESULTS IN CORROSION OF THE RESISTOR TERMINALS.

Consequence: CORROSION OF THE RESISTOR TERMINALS INCREASES ELECTRICALRESISTANCE, LEADING TO OVERHEATING AND POSSBLE IGNITION OF THE WIRING CONNECTORSAND INSULATION, CAUSING A FIRE IN THE COWL AREA.

Remedy: THE BLOWER MOTOR RESISTOR BLOCK WILL BE REPLACED, AND A MASTIC PATCH APPLIED TO SEAL THE COWL AGAINST WATER ENTRY. DAMAGED WIRE CONNECTORS WILL BE REPLACED.

Reported: 1991-11-01 (November 1, 1991) · Model years: 1990, 1991

THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE HOSE MAY LEAK OR DETACH AT ITS CRIMPED END FITTING RESULTING IN THE DISCHARGE OF HYDRAULIC FLUID.

Consequence: FLUID DISCHARGE EVENTUALLY CAUSES THE LOSS OF BOTH THEANTI-LOCK BRAKE SYSTEM AND HYDRAULIC ASSIST FOR THE BRAKE SYSTEM, RESULTING ININCREASED LIKELIHOOD OF BRAKE LOCKUP AND INCREASED STOPPING DISTANCES, WHICHCOULD RESULT IN A VEHICLE ACCIDENT.

Remedy: REPLACE THE ABS HIGH PRESSURE HOSE WITH A HOSE OF DIFFERENT DESIGN AND CONSTRUCTION.

Reported: 1996-06-13 (June 13, 1996) · Model years: 1990, 1991, 1992, 1993

THE ABS HYDRAULIC CONTROL UNIT CAN EXPERIENCE EXCESSIVE BRAKE ACTUATOR PISTON SEAL WEAR CAUSING PUMP-MOTOR DETERIORATION.

Consequence: IF THIS CONDITION OCCURS, THE ABS FUNCTION COULD BE LOST AND REDUCED POWER ASSIST WOULD BE EXPERIENCED DURING VEHICLE BRAKING INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL TEST THE VEHICLE'S ANTI-LOCK BRAKE SYSTEM AND REPAIR THE VEHICLES IF NECESSARY. ALSO THE WARRANTY ON ALL ABS COMPONENTS WILL BE EXTENDED TO 10 YEARS OR 100,000 MILES (EXCEPT FOR THE BRAKE ACTUATOR PISTON ASSEMBLY AND THE PUMP-MOTOR ASSEMBLY WHICH WILL HAVE A LIFETIME COVERAGE). OWNERS WILL ALSO BE REIMBURSED FOR PREVIOUS ABS COMPONENT REPAIR COSTS.

Reported: 1991-07-11 (July 11, 1991) · Model years: 1991

FRONT OUTBOARD SAFETY BELT MAY BECOME DIFFICULT TO LATCH AND OR UNLATCH DUE TO A WEBBING STIFFENER ENTERING THE BUCKLE HOUSING AND DISLODGING THE BUCKLE LATCH GUIDE.

Consequence: LATCH MAY OPEN DURING ACCIDENT OR SUDDEN STOP, EXPOSINGSEAT OCCUPANT TO INCREASED RISK OF INJURY.

Remedy: REPLACE BUCKLE LATCH ENGAGEMENT.

Reported: 1992-02-14 (February 14, 1992) · Model years: 1992

THE ZINC PLATING OPERATION PERFORMED ON THE UPPER STEERING COLUMN SHAFT COUPLING BOLT CAUSED HYDROGEN EMBRITTLEMENT AND BREAKAGE OF THE BOLT.

Consequence: FRACTURES OF THE UPPER STEERING COLUMN SHAFT COUPLINGBOLT RESULT IN A LACK OF COUPLING LOAD ON THE SHAFT AND LOSS OF STEERINGCONTROL.

Remedy: REPLACE THE ZINC PLATED BOLT WITH A PHOSPHATE PLATED BOLT.

Reported: 1998-08-06 (August 6, 1998) · Model years: 1993, 1994, 1995, 1996, 1997

VEHICLE DESCRIPTION: PASSENGER VEHICLES BUILT WITH 3.5L ENGINES. THE FUEL INJECTION DELIVERY SYSTEM CAN LEAK FUEL FROM SOME OF THE SEALING O-RINGS OR FROM HAIR LINE CRACKS IN THE THERMOSET FUEL INJECTION RAIL.

Consequence: FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE CAN RESULT IN A FIRE.

Remedy: DEALERS WILL REPLACE THE FUEL RAIL O-RINGS AND REINFORCE THE OUTLET (PASSENGER) SIDE FUEL RAIL. VEHICLES SHOWING FUEL LEAKAGE ON THE OUTLET FUEL RAIL MUST HAVE THE OUTLET RAIL REPLACED WHICH INCLUDES CHANGING THE UPPER AND LOWER INJECTOR O-RINGS. HOWEVER, IF A VEHICLE IS LEAKING FUEL FROM THE O-RINGS OR FROM A CRACKED FUEL LINE, THE VEHICLE SHOULD BE TAKEN INTO A DEALER TO HAVE THIS REPAIRED AS SOON AS POSSIBLE.

Reported: 1999-08-09 (August 9, 1999) · Model years: 1993, 1994, 1995

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM ATTACHING BRACKETS CAN CRACK DUE TO FATIGUE AND SEPARATE FROM THE ENGINE CRADLE.

Consequence: IF THIS OCCURS, THE TRANSMISSION HALF-SHAFT COULD PULL OUT OF THE TRANSAXLE AND RESULT IN LOSS OF POWER.

Remedy: DEALERS WILL REINFORCE THE ENGINE CRADLE AT THE POINT WHERE THE LOWER CONTROL ARM ATTACHES TO IT.

Reported: 1994-02-08 (February 8, 1994) · Model years: 1994

THE RIGHT STEERING TIE ROD CAN RUB THROUGH THE AUTOMATIC TRANSMISSION WIRING HARNESS CAUSING A SHORT CIRCUIT WHICH RESULTS IN ELECTRICAL SYSTEM MALFUNCTIONS INCLUDING ENGINE STALLING AND AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM.

Consequence: ELECTRICAL SYSTEM MALFUNCTION CAUSING STALLING WHILE IN MOTION OR AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM, WHICH ALLOWS ENGINE START WHILE THE TRANSMISSION IS NOT IN THE PARK POSITION, MAY RESULT IN AN ACCIDENT.

Remedy: INSTALL A REVISED WIRING HARNESS BRACKET AND A PLASTIC CONVOLUTED SLEEVE TO PROTECT THE TRANSMISSION WIRING HARNESS.