International Harvester 1853 recalls by model year

Reported: 1968-12-23 (December 23, 1968) · Model years: 1968

Reported: 1969-01-13 (January 13, 1969) · Model years: 1968

Reported: 1973-03-21 (March 21, 1973) · Model years: 1970, 1971

Reported: 1974-08-16 (August 16, 1974) · Model years: 1974

Reported: 1974-12-10 (December 10, 1974) · Model years: 1974

Reported: 1992-10-24 (October 24, 1992) · Model years: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987

THE SAGINAW GEAR DOES NOT RELIEVE PRESSURE WHEN THE WHEELS HAVE BEEN TURNED FULLY AGAINST THE AXLE STOPS. THE RESULTING CONTINUED PRESSURE ON THE STEERING SYSTEM CAN RESULT IN THE DEVELOPMENT OF CRACKS IN THE SPLINES OF THE PITMAN SHAFT, WHICH CAN DEVELOP INTO A COMPLETE FRACTURE OF THE PITMAN SHAFT.

Consequence: FRACTURE OF THE PITMAN SHAFT CAUSES COMPLETE LOSS OFSTEERING CONTROL, WHICH COULD RESULT IN A VEHICLE ACCIDENT IF FRACTURE OCCURSWHILE VEHICLE IS IN MOTION.

Remedy: REPLACE THE EXISTING PITMAN SHAFT IN THE STEERING GEAR ASSEMBLY WITH A NEW, STRENGTHENED PITMAN SHAFT.

Reported: 1992-07-20 (July 20, 1992) · Model years: 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1991, 1992

THE FUEL SYSTEM FAILED THE CRASH BARRIER TEST.

Consequence: THE FUEL TANK WAS PUNCTURED, RESULTING IN FLUID LOSSGREATER THAN ALLOWED BY FMVSS 301, "FUEL SYSTEM INTEGRITY". FUEL SPILLS INA COLLISION COULD LEAD TO A VEHICLE FIRE IF EXPOSED TO A SOURCE OF IGNITION.

Remedy: MODIFY THE FUEL TANK CAGE TO COMPLY WITH FMVSS 301.

Reported: 1996-11-12 (November 12, 1996) · Model years: 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1991, 1992

THESE BUSES HAVE A TURN SIGNAL LEVER THAT WILL NOT OPERATE CONSISTENTLY IN THE LANE CHANGE MODE IF THE LEVER IS NOT MOVED TO THE POSITION WHERE RESISTANCE TO MOVEMENT IS FELT.

Consequence: SHOULD THE REAR SIGNAL LAMPS NOT FLASH WHEN A LANE CHANGE WAS BEING MADE, IT COULD RESULT IN A VEHICLE FOLLOWING THE BUS TO COLLIDE WITH THE BUS INCREASING THE RISK OF PERSONAL INJURY AND/OR PROPERTY DAMAGE.

Remedy: OPERATORS WILL BE MAILED INFORMATION CONCERNING THE PROPER METHOD OF USING TURN SIGNALS. A DECAL WILL ALSO BE PROVIDED TO BE PLACED ON THE INSTRUMENT PANEL OF EACH BUS.

Reported: 1996-06-11 (June 11, 1996) · Model years: 1982

THE AXLE HOUSINGS WERE MANUFACTURED WITH A TIGHT FRICTION WELD CURL RADIUS ON THE INSIDE DIAMETER OF THE AXLE HOUSING. UNDER OPERATIONAL LOADS, CRACKS CAN INITIATE AT THE WELD CURL RADIUS ON THE INSIDE OF THE HOUSING. THESE CRACKS MAY PROPAGATE, EVENTUALLY ALLOWING THE AXLE SPINDLE TO SEPARATE FROM THE AXLE HOUSING.

Consequence: SEPARATION OF THE AXLE SPINDLE FROM THE AXLE HOUSING CAN RESULT IN LOSS OF VEHICLE CONTROL AND A POSSIBLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HOUSING WITH A NEW HOUSING.