Gmc C20 recalls by model year

Reported: 1977-06-22 (June 22, 1977) · Model years: 1975

THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.

Remedy: DEALER WILL INSPECT AND, WHERE NECESSARY, WILL REPLACE THE BALL JOINTS WITHOUT CHARGE TO OWNER.

Reported: 1977-10-14 (October 14, 1977) · Model years: 1976, 1977

THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVER"S FOOT IS REMOVED FROM THE PEDAL.

Remedy: DEALER WILL INSTALL A NEW ACCELERATOR PEDAL AND RETAINER DESIGNED TO PREVENT THE ACCELERATOR PEDAL ROD FROM CUTTING THE RUBBER MAT OR CARPET. THIS WILL BE PERFORMED WITHOUT CHARGE.

Reported: 1979-06-06 (June 6, 1979) · Model years: 1979

ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH AT NO COST TO OWNER.

Reported: 1981-01-13 (January 13, 1981) · Model years: 1979, 1980

FATIGUE CRACKS MAY DEVELOP IN THE BRAKE VACUUM BOOSTER HOUSING. THIS MAY CAUSE A VACUUM LEAK AND REDUCE THE EFFECTIVENESS OF THE BRAKES. AFTER PROLONGED USE, THE CRACKS MAY DEVELOP TO THE EXTENT THAT THE BOOSTER MAY SEPARATE FROM THE VEHICLE.

Remedy: VEHICLES WILL BE INSPECTED FOR FATIGUE CRACKS IN THE BRAKE VACUUM BOOSTER. THOSE WITHOUT CRACKS WILL HAVE A SUPPORT BRACE INSTALLED. THOSE WITH EVIDENCE OF CRACKING WILL HAVE A NEW BRAKE VACUUM BOOSTER AND SUPPORT BRACE INSTALLED. THIS SERVICE WILL BE PROVIDED AT NO CHARGE.

Reported: 1981-12-14 (December 14, 1981) · Model years: 1981

THE HYDRAULIC BRAKE FLUID USED IN CERTAIN VEHICLES MAY FAIL TO COMPLY WITH THE BRAKE FLUID BOILING POINT REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 116, "MOTOR VEHICLE BRAKE FLUIDS". BRAKING EFFICIENCY MAY BE REDUCED AND VEHICLE STOPPING DISTANCE INCREASED, ESPECIALLY WHEN HARD OR FREQUENT BRAKING RAISES BRAKE FLUID TEMPERATURE.

Remedy: SUSPECT HYDRAULIC BRAKE FLUID WILL BE BLED FROM THE BRAKE SYSTEM AND REPLACED WITH GM DELCO SUPREME NO. 11 OR AN EQUIVALENT, WITHOUT CHARGE.

Reported: 1982-08-24 (August 24, 1982) · Model years: 1982

THE REAR AXLE SHAFTS RECEIVED IMPROPER HEAT TREATMENT DURING MANUFACTURE. THE SHAFT MAY BREAK AND THE TIRE AND WHEEL ASSEMBLY COULD DISENGAGE FROM THE VEHICLE.

Remedy: DEALER WILL REPLACE BOTH REAR AXLE SHAFT ASSEMBLIES, IF NECESSARY, FREE OF CHARGE.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1990-06-04 (June 4, 1990) · Model years: 1990

LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.

Consequence: THIS COULD CAUSE LOSS OF BRAKING ACTIVITY THAT COULDRESULT IN A TRUCK CRASH WITHOUT PRIOR WARNING.

Remedy: RETORQUE BRAKE PEDAL PIVOT BOLTS TO SPECIFICATIONS TO PREVENT LOOSENING.